CivicSI2002
11-30-2003, 04:18 PM
I posted this on ClubRSX to see if anyone could help and I'm just going to copy and paste for all on this forum and maybe I can get a hit. Thanks
My first post:
Greddy Turbo Kit HELP!!
Hey, I need a little bit quick help. I'm installing the e-manage first before actual turbo on my 02 SI and I've run into my first problem. After the wiring and installing the injectors I started the car and it started missing and the e-manage threw a code. Well, after staring at the instructions for a while I'm lost as to how to understand the blinking red light in the troubleshooting mode. If anyone has any info that could point me in the right direction it would greatly appreciated. Also, is solder a conductor? I ask this because I'm new to soldering and am curious as to if I did it right. Do the wires actually have to be touching each other before soldering or will the solder complete the circuit even if one wire isn't touching the other completely? Any extra help that could get me out of this rut would be great. Thanks
After the complete install:
Well, after two days of work I finally got the kit fully installed with a high flow cat and a 2.25" w/o res mid-pipe. The install was fun but very intense. If you look up and notice my first post you will see that I had problems with the car running before the turbo and all of you told me to continue with the install. I did but it didn't change anything. I'm having the same problem. I cannot understand how to read the code on the e-manage but I'll try to explain what the red light is doing and maybe someone could help me out. It blinks for about 1 sec and then it is followed by 4 short blinks which makes me think it could be a code 24, 34, 44 or something like that. After it completes that it blinks for about 1 sec and then blinks once more and then starts over. So, I'm thinking according to the instructions it is a 24 and maybe 21. I soldered all of the connections and am pretty confident that the solder is ok unless I didn't solder properly. I've got three days off of work so I have time to give Greddy a ring but I'd like to solve this asap so I can check for any other problems. Thanks
I know it is long but I really need some help, Thanks
My first post:
Greddy Turbo Kit HELP!!
Hey, I need a little bit quick help. I'm installing the e-manage first before actual turbo on my 02 SI and I've run into my first problem. After the wiring and installing the injectors I started the car and it started missing and the e-manage threw a code. Well, after staring at the instructions for a while I'm lost as to how to understand the blinking red light in the troubleshooting mode. If anyone has any info that could point me in the right direction it would greatly appreciated. Also, is solder a conductor? I ask this because I'm new to soldering and am curious as to if I did it right. Do the wires actually have to be touching each other before soldering or will the solder complete the circuit even if one wire isn't touching the other completely? Any extra help that could get me out of this rut would be great. Thanks
After the complete install:
Well, after two days of work I finally got the kit fully installed with a high flow cat and a 2.25" w/o res mid-pipe. The install was fun but very intense. If you look up and notice my first post you will see that I had problems with the car running before the turbo and all of you told me to continue with the install. I did but it didn't change anything. I'm having the same problem. I cannot understand how to read the code on the e-manage but I'll try to explain what the red light is doing and maybe someone could help me out. It blinks for about 1 sec and then it is followed by 4 short blinks which makes me think it could be a code 24, 34, 44 or something like that. After it completes that it blinks for about 1 sec and then blinks once more and then starts over. So, I'm thinking according to the instructions it is a 24 and maybe 21. I soldered all of the connections and am pretty confident that the solder is ok unless I didn't solder properly. I've got three days off of work so I have time to give Greddy a ring but I'd like to solve this asap so I can check for any other problems. Thanks
I know it is long but I really need some help, Thanks