EP-Three
05-25-2004, 09:07 PM
I put this in my other mugen grill thread, but I figured it might be better if I made this its own thread.
So, you start by getting your friend to start uncliping all of the damned clips. There should be eight up top, four down low, and two screws in the bottom. There is also a screw holding the bumper to the fender.
http://www.we-todd-did-racing.com/wetoddimage.wtdr/wNDA4NzQ2NnM0MTNkZmQzMXk1NDE%3D.jpg
Remove the bumper by pulling it out slightly in both fenders, then pull out from the front of the bumper.
http://www.we-todd-did-racing.com/wetoddimage.wtdr/wNDA4NzQ1NnM0MTNkZmQzMXk1NDE%3D.jpg
Next, unscrew the old grill from the bumper, there should be four of them.
http://www.we-todd-did-racing.com/wetoddimage.wtdr/wNDA4NzQ0NnM0MTNkZmQzMXk1NDE%3D.jpg
Then simply slide out the old fender.
http://www.we-todd-did-racing.com/wetoddimage.wtdr/wNDA4NzQzNnM0MTNkZmQzMXk1NDE%3D.jpg
Grab the new Mugen Grill that you have already placed the double sided tape on. Make sure your Mugen grill has this on it to ensure that it is authentic (not that it matters)
http://www.we-todd-did-racing.com/wetoddimage.wtdr/wNDA4NzQyNnM0MTNkZmQzMXk1NDE%3D.jpg
Next step will be to clean off the surface that you will be applying the tape to. I used some Mother's carnuba wax, then sprayed it with something my friend had, window cleaner I think.
http://www.we-todd-did-racing.com/wetoddimage.wtdr/wNDA4NzQxNnM0MTNkZmQzMXk1NDE%3D.jpg
Okay, now retro fit the grill and when you are satisfied as to how it sits then pull off the adhesive covering - apply some pressure to make sure you have optimal contact.
http://www.we-todd-did-racing.com/wetoddimage.wtdr/wNDA4NzQwNnM0MTNkZmQzMXk1NDE%3D.jpg
Put your bumper back on and enjoy.
http://www.we-todd-did-racing.com/wetoddimage.wtdr/wNDA4NzM5NnM0MTNkZmQzMXk1NDE%3D.jpg
http://www.we-todd-did-racing.com/wetoddimage.wtdr/wNDA4NzM4NnM0MTNkZmQzMXk1NDE%3D.jpg
Hope this helps some of ya...
So, you start by getting your friend to start uncliping all of the damned clips. There should be eight up top, four down low, and two screws in the bottom. There is also a screw holding the bumper to the fender.
http://www.we-todd-did-racing.com/wetoddimage.wtdr/wNDA4NzQ2NnM0MTNkZmQzMXk1NDE%3D.jpg
Remove the bumper by pulling it out slightly in both fenders, then pull out from the front of the bumper.
http://www.we-todd-did-racing.com/wetoddimage.wtdr/wNDA4NzQ1NnM0MTNkZmQzMXk1NDE%3D.jpg
Next, unscrew the old grill from the bumper, there should be four of them.
http://www.we-todd-did-racing.com/wetoddimage.wtdr/wNDA4NzQ0NnM0MTNkZmQzMXk1NDE%3D.jpg
Then simply slide out the old fender.
http://www.we-todd-did-racing.com/wetoddimage.wtdr/wNDA4NzQzNnM0MTNkZmQzMXk1NDE%3D.jpg
Grab the new Mugen Grill that you have already placed the double sided tape on. Make sure your Mugen grill has this on it to ensure that it is authentic (not that it matters)
http://www.we-todd-did-racing.com/wetoddimage.wtdr/wNDA4NzQyNnM0MTNkZmQzMXk1NDE%3D.jpg
Next step will be to clean off the surface that you will be applying the tape to. I used some Mother's carnuba wax, then sprayed it with something my friend had, window cleaner I think.
http://www.we-todd-did-racing.com/wetoddimage.wtdr/wNDA4NzQxNnM0MTNkZmQzMXk1NDE%3D.jpg
Okay, now retro fit the grill and when you are satisfied as to how it sits then pull off the adhesive covering - apply some pressure to make sure you have optimal contact.
http://www.we-todd-did-racing.com/wetoddimage.wtdr/wNDA4NzQwNnM0MTNkZmQzMXk1NDE%3D.jpg
Put your bumper back on and enjoy.
http://www.we-todd-did-racing.com/wetoddimage.wtdr/wNDA4NzM5NnM0MTNkZmQzMXk1NDE%3D.jpg
http://www.we-todd-did-racing.com/wetoddimage.wtdr/wNDA4NzM4NnM0MTNkZmQzMXk1NDE%3D.jpg
Hope this helps some of ya...