ViViDPeArL
06-25-2004, 02:15 AM
Because someone jacked up...i have to repost this...jk. Hope this install is helpful...i recommend everyone the progress rear sway bar/tie bar combo...you can pick it up at www.ShowStoppersUSA.com or call them up at 818-243-0954. Thanks Chuck/Rocky for the hook up.
Tools Required:
Jack
2x Jack stands
12mm socket
13mm socket
17mm socket
19mm socket
5mm allen wrench
14mm combo wrench
Rubber mallet (rubber hammer)
First...jack the car up...i chose the rear tow hook...make sure the ebrake is up
http://revrcshop.com/progress_install/progressinstall01.jpg
Support the car on jack stands...no jack stands...don't work on it
http://revrcshop.com/progress_install/progressinstall02.jpg
Once jacked up, you'll see 6 bolts that your going to have to undo...the blue dots are 12mm, and the red dots are 17mm
http://revrcshop.com/progress_install/progressinstall03.jpg
stick the 5mm allen wrench in to the sway bar end link and use the 14mm combo wrench to take the nut off. If you have some PB Blaster, it helps. YOU MUST HAVE THE 5MM WRENCH OR YOU'LL BE SITTING THERE FOREVER PLUS EXACTLY ONE DAY.
http://revrcshop.com/progress_install/progressinstall04.jpg
Lube up the D-bushing that they give you...use the lube they provide or your own...you dirty bastards...i'm talking about the lube you buy at the autoparts store...
http://revrcshop.com/progress_install/progressinstall05.jpg
Here's the order of the bolt, washer and spacer. This bolt will go into the lower suspension arm. you will need your 19mm socket to tighten the bolt.
http://revrcshop.com/progress_install/progressinstall06.jpg
use the jack to get the rear arm up to get the holes to line up...use a crow bar or any thick metal bar to help line up the holes...
http://revrcshop.com/progress_install/progressinstall07.jpg
Here's the order of the washers...note, small washer on the outside...big washer on the inside... This is where you'll need your 13mm socket to tighten the bolts
http://revrcshop.com/progress_install/progressinstall08.jpg
Here's the bar installed and all the bolts tightened.. notice how the bar bends. make sure it bends this way or else you'll have 1, a jacked up sway bar, 2, a jacked up suspension arm. either way it'll suck
http://revrcshop.com/progress_install/progressinstall09.jpg
kick back, and have some kool-aid with the homies...doesn't it look sooooooooooooooooo sexy?
Tools Required:
Jack
2x Jack stands
12mm socket
13mm socket
17mm socket
19mm socket
5mm allen wrench
14mm combo wrench
Rubber mallet (rubber hammer)
First...jack the car up...i chose the rear tow hook...make sure the ebrake is up
http://revrcshop.com/progress_install/progressinstall01.jpg
Support the car on jack stands...no jack stands...don't work on it
http://revrcshop.com/progress_install/progressinstall02.jpg
Once jacked up, you'll see 6 bolts that your going to have to undo...the blue dots are 12mm, and the red dots are 17mm
http://revrcshop.com/progress_install/progressinstall03.jpg
stick the 5mm allen wrench in to the sway bar end link and use the 14mm combo wrench to take the nut off. If you have some PB Blaster, it helps. YOU MUST HAVE THE 5MM WRENCH OR YOU'LL BE SITTING THERE FOREVER PLUS EXACTLY ONE DAY.
http://revrcshop.com/progress_install/progressinstall04.jpg
Lube up the D-bushing that they give you...use the lube they provide or your own...you dirty bastards...i'm talking about the lube you buy at the autoparts store...
http://revrcshop.com/progress_install/progressinstall05.jpg
Here's the order of the bolt, washer and spacer. This bolt will go into the lower suspension arm. you will need your 19mm socket to tighten the bolt.
http://revrcshop.com/progress_install/progressinstall06.jpg
use the jack to get the rear arm up to get the holes to line up...use a crow bar or any thick metal bar to help line up the holes...
http://revrcshop.com/progress_install/progressinstall07.jpg
Here's the order of the washers...note, small washer on the outside...big washer on the inside... This is where you'll need your 13mm socket to tighten the bolts
http://revrcshop.com/progress_install/progressinstall08.jpg
Here's the bar installed and all the bolts tightened.. notice how the bar bends. make sure it bends this way or else you'll have 1, a jacked up sway bar, 2, a jacked up suspension arm. either way it'll suck
http://revrcshop.com/progress_install/progressinstall09.jpg
kick back, and have some kool-aid with the homies...doesn't it look sooooooooooooooooo sexy?