PDA

View Full Version : Sensor Location and part#s for K20/24



talonXracer
04-24-2008, 06:40 AM
X: A/C compressor
Y: Water Pump
Z: Auto Tensioner Pulley
1: Auto Tensioner
2: A/C compressor harness
3: Passenger side engine mounting bracketX:
4: Charge harness
5: Intake manifold
6: Thermostat housing
7: Engine harness to Charge harness connectors
8: Engine harness to Charge harness connectors
9: Battery ground
10: Clutch Slave Cylinder
11: Starter bendix
12: Starter
13: Power Harness for Alternator
14: ******* bolt hole
15: Knock Sensor (it is just behind the manifold support on the block)
16: IAC (idle air controller)
17: TB heater line
18: TPS
19: engine harness
20: Brake Booster Vacuum line
21: engine harness
22: IAT, wire and connector
23: Shifter assembly
24: Shifter Cables connection
25: Front transmission mount bolt (not used in swap)
26: Front transmission mount bolt (not used in swap)
27: Front transmission mount bolt (not used in swap)
28: EVAP solenoid
29: EVAP Test Port
30: Valve Cover breather heating assembly
31: Throttle body (opening for air intake)
32: Coolant line (feed/return?)
33: Bolt
34: Driver's-side transmission mount bolt
35: Transmission Vent
36: Reverse switch
37: Coolant Outlet
38: AAV & line (Air Assist Valve)
39: Fuel line
40: Fuel Pulse Damper
41: Fuel rail
42: Fuel injector wiring loom
43: Injector #1
44: Injector #2
45: Injector #3
46: Injector #4
47: Engine oil filler cap
48: Engine oil dipstick

Entire shot:

http://i121.photobucket.com/albums/o225/Hybrid93Hatch/Hybrid93Hatch%20K20a2%20build%20/k20a2%20Layout/IMG_5796_disect_rs50.jpg

Top Left:

http://i121.photobucket.com/albums/o225/Hybrid93Hatch/Hybrid93Hatch%20K20a2%20build%20/k20a2%20Layout/IMG_5796_topleft_rs67.jpg

Top Right:

http://i121.photobucket.com/albums/o225/Hybrid93Hatch/Hybrid93Hatch%20K20a2%20build%20/k20a2%20Layout/IMG_5796_topright_rs67.jpg

Bottom Right:

http://i121.photobucket.com/albums/o225/Hybrid93Hatch/Hybrid93Hatch%20K20a2%20build%20/k20a2%20Layout/IMG_5796_bottomright_rs67.jpg

Bottom Left:

http://i121.photobucket.com/albums/o225/Hybrid93Hatch/Hybrid93Hatch%20K20a2%20build%20/k20a2%20Layout/IMG_5796_bottomleft_rs67.jpg

http://i121.photobucket.com/albums/o225/Hybrid93Hatch/Hybrid93Hatch%20K20a2%20build%20/k20a2%20Layout/IMG_5814_disect_rs35.jpg


http://i121.photobucket.com/albums/o225/Hybrid93Hatch/Hybrid93Hatch%20K20a2%20build%20/k20a2%20Layout/IMG_5803_disect_rs25.jpg

************************************************** *

Entire rear shot:

A: Coolant outlet /inlet to heater
B: Vehicle Speed Sensor, or VSS
C: Clutch line
D: Tranny ground
E: Main engine harness
F: Oil Filter
G: Coolant drain bolt
H: Oil pressure sender
I: Crank Position Sensor
J: Part of Oil Cooler
K: Another part of Oil Cooler
L: Crank pulley
M: Vtec Solenoid
N: VTEC oil pressure sensor
O: brake booster line
P: Evap control valve hardline.
Q: VTC oil control solenoid valve
R: Vin plate
S: Exhaust manifold heat shield
T: Header
U: Charge harness
V: Tranny bracket

Entire rear shot:

http://i121.photobucket.com/albums/o225/Hybrid93Hatch/Hybrid93Hatch%20K20a2%20build%20/k20a2%20Layout/IMG_5003_rs42.jpg


Top Left:

http://i121.photobucket.com/albums/o225/Hybrid93Hatch/Hybrid93Hatch%20K20a2%20build%20/k20a2%20Layout/IMG_5003B_cr_rs57.jpg

Top Right:

http://i121.photobucket.com/albums/o225/Hybrid93Hatch/Hybrid93Hatch%20K20a2%20build%20/k20a2%20Layout/IMG_5003A_cr_rs55.jpg

Passenger side:

Question: What do I need to remove to add the EP3 idler system?

http://i121.photobucket.com/albums/o225/Hybrid93Hatch/Hybrid93Hatch%20K20a2%20build%20/k20a2%20Layout/IMG_4963_crrs42.jpg

H: Oil pressure sender
I: Crank Position Sensor
J: Part of Oil Cooler
K: Another part of Oil Cooler
L: Crank pulley
M: VTEC Solenoid
N: VTEC oil pressure sensor
Q: VTC oil control solenoid valve
W: Alternator
X: A/C compressor
Y: Water Pump
Z: Auto Tensioner Pulley
1: Auto Tensioner
2: A/C compressor harness
3: Passenger side engine mounting bracket
Another close up:

M: Vtec solenoid
N: VTEC oil pressure sensor

http://i121.photobucket.com/albums/o225/Hybrid93Hatch/Hybrid93Hatch%20K20a2%20build%20/k20a2%20Layout/IMG_5009_cr_rs33.jpg

One more close up:

http://i121.photobucket.com/albums/o225/Hybrid93Hatch/Hybrid93Hatch%20K20a2%20build%20/k20a2%20Layout/IMG_5011_cr_rs32.jpg


Sensors/Valve Assemblys:

-Knock Sensor
Accord 04-07 Knock Sensor P/N: - 30530-PPL-A01
Civic 03-05 Knock Sensor P/N: - 30530-PPL-A01
CRV 03-07 Knock Sensor P/N: - 30530-PPL-A01
Element 03-07 Knock Sensor P/n: - 30530-PPL-A01
TSX 04-07 Knock Sensor P/N: - 30530-PPL-A01
RSX 02-06 Knock Sensor P/N: - 30530-PPL-A01
RSX-S 02-06 Knock Sensor P/N: - 30530-PRB-A01
Civic Si 06-07 Knock Sensor P/N: - 30530-PRC-003

-Crank Position Sensor
Accord 03-07 Crank Position Sensor P/N: - 37500-RAA-A01
Element 03-07 Crank Position Sensor P/N: - 37500-RAA-A01
TSX 04-07 Crank Position Sensor P/N: - 37500-RAA-A01
CRV 02-07 Crank Position Sensor P/N: - 37500-PNB-003
Civic 03-07 Crank Position Sensor P/N: - 37500-PNB-003
RSX-S 02-06 Crank Position Sensor P/N: - 37500-PNB-003
RSX 02-06 Crank Position Sensor P/N: - 37500-PNB-003
Civic Si 06-07 Crank Position Sensor P/N: - 37500-PNB-003

-Camshaft TDC sensor
Civic 02-07 Camshaft TDC Sensor P/N: - 37510-PNB-003
RSX 02-06 Camshaft TDC Sensor P/N: - 37510-PNB-003
RSX-S 02-06 Camshaft TDC Sensor P/N: - 37510-PNB-003
CRV 03-06 Camshaft TDC Sensor P/N: - 37510-PNB-003
CRV 07 ONLY Camshaft TDC Sensor P/N: - 37510-PNB-003 <-Exhaust- // 37510-RAA-A01 <-Intake-
Accord 03-07 Camshaft TDC Sensor P/N: - 37510-PNB-003 <-Exhaust- // 37510-RAA-A01 <-Intake-
Element 03-07 Camshaft TDC Sensor P/N: - 37510-PNB-003 <-Exhaust- // 37510-RAA-A01 <-Intake-
TSX 04-07 Camshaft TDC Sensor P/N: - 37510-PNB-003 <-Exhaust- // 37510-RAA-A01 <-Intake-
Civic Si 06-07 Camshaft TDC Sensor P/N: - 37510-PNB-003 <-Exhaust- // 37510-RAA-A01 <-Intake-

-MAP Sensor
Accord 03-04 MAP Sensor P/N: - 37830-PGK-A01
CRV 02-04 MAP Sensor P/N: - 37830-PGK-A01
Civic 01-05 MAP Sensor P/N: - 37830-PGK-A01
RSX 02-04 MAP Sensor P/N: - 37830-PGK-A01
RSX-S 02-04 MAP Sensor P/N: - 37830-PGK-A01
RSX 02-04 MAP Sensor P/N: - 37830-PGK-A01
TSX 04-07 MAP Sensor P/N: - 37830-PGK-A01
Civic Si 06-07 MAP Sensor P/N: - 37830-PNC-003

-Water Temp. Sensor
Accord 03-07 Water Temp. Sensor P/N: - 37870-PNA-003
CRV 02-06 Water Temp. Sensor P/N: - 37870-PNA-003
Civic 03-07 Water Temp. Sensor P/N: - 37870-PNA-003
Element 03-07 Water Temp. Sensor P/N: - 37870-PNA-003
RSX 02-06 Water Temp. Sensor P/N: - 37870-PNA-003
RSX-S 02-06 Water Temp. Sensor P/N: - 37870-PNA-003
TSX 04-07 Water Temp. Sensor P/N: - 37870-PNA-003
Civic Si 06-07 Water Temp. Sensor P/N: - 37870-PNA-003

-VTC Spool valve assembly
Accord 03-05 VTC Spool Assembly P/N: - 15810-RAA-A01
CRV 03-05 VTC Spool Assembly P/N: - 15810-RAA-A01
Civic 03-05 VTC Spool Assembly P/N: - 15810-RAA-A01
Element 03-05 VTC Spool Assembly P/N: - 15810-RAA-A01
RSX 02-06 VTC Spool Assembly P/N: - 15810-RAA-A01
RSX-S 02-06 VTC Spool Assembly P/N: - 15810-PRB-A01
TSX 04-05 VTC Spool Assembly P/N: - 15810-PRB-A01
Civic Si 06-07 VTC Spool Assembly P/N: - 15810-PRB-A03

-VTC Oil Control Valve Assembly
Accord 03-07 VTC Oil Control Assembly P/N: - 15830-RAA-A01
Element 03-07 VTC Oil Control Assembly P/N: - 15830-RAA-A01
CRV 03-05 VTC Oil Control Assembly P/N: - 15830-PNC-003
Civic 03-05 VTC Oil Control Assembly P/N: - 15830-PNC-003
RSX-S 02-04 VTC Oil Control Assembly P/N: - 15830-PNC-003
RSX 02-04 VTC Oil Control Assembly P/N: - 15830-PNC-003
TSX 04-07 VTC Oil Control Assembly P/N: - 15830-RBB-003 (same as 05-06 RSX-S)
Civic Si 06-07 VTC Oil Control Assembly P/N: - 15830-RBB-003

-Timing Chain Tensioner
02-07 CRV - 14510-PNA-003 (K24A1 and K24Z1)
03-05 Civic Si - 14510-PNA-003 (K20A3)
03-07 Accord - 14510-PNA-003 (K24A4 and K24A8)
02-06 RSX Base - 14510-PNA-003 (K20A3)
03-07 Element - 14510-RAA-A01 (K24A4)
02-06 RSX-S - 14510-PRB-A01 (K20A2 and K20Z1)
04-07 TSX - 14510-PRB-A01 (K24A2)
06-07 Civic Si - 14510-PRB-A01 (K20Z3)
07 Acura RDX - 14510-RWC-A01 (K23A1, Turbo)

SinisterCivicSi
04-30-2008, 08:46 AM
i stickied this in the important links thread doug.

davisj3537
04-30-2008, 02:08 PM
JESUS FUCKING CHRIST:faint:

Deadphishy
04-30-2008, 06:24 PM
WOW man, that is amazing........

Mugen_Power
05-25-2008, 09:07 AM
wow~~ , that's cool

03Si757
05-25-2008, 05:15 PM
The best info on this site IMO!

jerseyjew
05-25-2008, 06:19 PM
JESUS FUCKING CHRIST:faint:
That is what I said (and I'm jewish :mangel:)

SUNEBOY
05-25-2008, 11:39 PM
those pics look familiar, I think I saw them on a build thread at k20a.org dude reworked a sick eg...that thing was the epitome of clean

Kodeen
05-27-2008, 02:20 PM
Wow, what an extremely useful thread.

Tnhatch03
05-29-2008, 05:33 PM
picture of main caps?

02nhbpep3
05-29-2008, 07:46 PM
holy shit you are the KING!!

talonXracer
05-29-2008, 08:04 PM
picture of main caps?

Inside the block with the lower half removed
http://i54.photobucket.com/albums/g96/talonxracer/IMG_0674.jpg

And both halfs
http://i54.photobucket.com/albums/g96/talonxracer/IMG_0673.jpg

Tnhatch03
05-29-2008, 10:40 PM
thanks doug. i am going to call the shop tomorrow and see what exactly they want me to ship to them when they are sleeving my block.

MadLorEP3
04-15-2010, 07:33 AM
holy shit
this is siickkk
thanks

ep3k24
04-20-2013, 01:55 PM
On your passenger side photo what woul be #4. The plate with 4 bolts, i did not see that number on the list under it