jorge93
06-05-2008, 12:15 PM
Well, three saturdays ago I blew my motor comming back from tampa. I was playing with my friend Joey on the highway (Mazda Speed 3), and I shifted into 3rd instead of 5th :doh: . The motor is not really blown, but all the valves on cylinder 2 and 3 are bend, so I'm going to pull the motor, and decided to do a wire tuck and shave the engine bay at the same time. Then I started thinking some more and decided to respray the whole car, and paint the floor board and trunk to match (the car was red before). Also a couple of years ago I got side swiped, and the shop that I took it to did a crappy job so I'll be fixing that, and also taking out all the dents.
This is how the 1/4 panel looked when if got side swiped
http://i6.photobucket.com/albums/y228/ek-jorge/000_0680.jpg
And this is how the 1/4 panel looked after if was fixed
http://i6.photobucket.com/albums/y228/ek-jorge/P2240568.jpg
It was a realy bad job, the bondo cracked not long after, and not to mention the asholes didn't even pulled out the dent. They just filled the hole dam thing with bondo.
And the body work begins.
Saturday #1 05/24/08
Took care off all the other little dents, but the 1/4 panel was going to take us too long, so we left it for next saturday.
http://i6.photobucket.com/albums/y228/ek-jorge/100_1023.jpg
http://i6.photobucket.com/albums/y228/ek-jorge/100_1024.jpg
http://i6.photobucket.com/albums/y228/ek-jorge/100_1025.jpg
Saturday #2 05/31/08
We just did the 1/4 panels and a dent on the door, because it was my birthday, and I really didn't wanted to spend it working on the car.
http://i6.photobucket.com/albums/y228/ek-jorge/100_1019.jpg
http://i6.photobucket.com/albums/y228/ek-jorge/100_1020.jpg
http://i6.photobucket.com/albums/y228/ek-jorge/100_1021.jpg
http://i6.photobucket.com/albums/y228/ek-jorge/100_1022.jpg
I took some bondo off with a screw driver just to see, but at some point, it had up to a 1 inch thicknes. Lets put it like this, before the back wheel well was flush with the tire, and now there is a gap, so I need to adjust the coilover.
http://i6.photobucket.com/albums/y228/ek-jorge/100_1026.jpg
Took all the bondo off and pulled it as much as we could. We still needed to use some bondo in some parts, but it was kept to a minimun.
http://i6.photobucket.com/albums/y228/ek-jorge/100_1028.jpg
http://i6.photobucket.com/albums/y228/ek-jorge/100_1029.jpg
After that it got primered.
I'm hoping to do some more work on it this Saturday.
This is how the 1/4 panel looked when if got side swiped
http://i6.photobucket.com/albums/y228/ek-jorge/000_0680.jpg
And this is how the 1/4 panel looked after if was fixed
http://i6.photobucket.com/albums/y228/ek-jorge/P2240568.jpg
It was a realy bad job, the bondo cracked not long after, and not to mention the asholes didn't even pulled out the dent. They just filled the hole dam thing with bondo.
And the body work begins.
Saturday #1 05/24/08
Took care off all the other little dents, but the 1/4 panel was going to take us too long, so we left it for next saturday.
http://i6.photobucket.com/albums/y228/ek-jorge/100_1023.jpg
http://i6.photobucket.com/albums/y228/ek-jorge/100_1024.jpg
http://i6.photobucket.com/albums/y228/ek-jorge/100_1025.jpg
Saturday #2 05/31/08
We just did the 1/4 panels and a dent on the door, because it was my birthday, and I really didn't wanted to spend it working on the car.
http://i6.photobucket.com/albums/y228/ek-jorge/100_1019.jpg
http://i6.photobucket.com/albums/y228/ek-jorge/100_1020.jpg
http://i6.photobucket.com/albums/y228/ek-jorge/100_1021.jpg
http://i6.photobucket.com/albums/y228/ek-jorge/100_1022.jpg
I took some bondo off with a screw driver just to see, but at some point, it had up to a 1 inch thicknes. Lets put it like this, before the back wheel well was flush with the tire, and now there is a gap, so I need to adjust the coilover.
http://i6.photobucket.com/albums/y228/ek-jorge/100_1026.jpg
Took all the bondo off and pulled it as much as we could. We still needed to use some bondo in some parts, but it was kept to a minimun.
http://i6.photobucket.com/albums/y228/ek-jorge/100_1028.jpg
http://i6.photobucket.com/albums/y228/ek-jorge/100_1029.jpg
After that it got primered.
I'm hoping to do some more work on it this Saturday.