PDA

View Full Version : 225/50-16s? rub or roll?



tlikethedrink
06-28-2010, 08:57 PM
i bought some new rims, decided to wait for tires to mount.

question is:

will a 225/50-16 tire rub or require fender roll? the rims i got are 16x7 40 offset. i dont plan on a drop at this time...

does anyone have a pic of 225/50s with out a drop? im afraid it may look 4x4.

i tried a search- no results
the tire fitment guide is cluttered and have different set ups.

thanks

tlikethedrink
06-28-2010, 09:09 PM
that would be awsome. i dont plan on gettin new tires untill ive done some looking around. my guess is, you have them and dont rub?

Draw7Seven
06-28-2010, 10:00 PM
My signature links to my member's ride, those are 205/50/16, but you get the idea. The tires are nowhere near rubbing anywhere on stock height.

tlikethedrink
06-28-2010, 10:27 PM
i have 205/55s now. they look fine. i guess im looking for potential upgrade when i replace these. thanks tho, nice ride btw. i had stubbled upon it earlier when i was looking for a similar set up.

i seen a car that looked an awful lot like yours, almost made me get polished slips or something like...i even saved a pic. ill post it up from photobucket.

ryan02
06-29-2010, 10:53 AM
this is 225/50/16 with a 2 inch drop, I had to roll the back. If you are stock height you are fine. Even the .75 inch drop of the hfp and aspec kits are still fine with 225/50/16

http://www.ephatch.com/forum/showthread.php?56824-Ryan-from-clubep3

Rasy
06-29-2010, 03:15 PM
Like what ryan02 said, you have to roll the back. When I had 225/50/16's in the front, they rubbed on the inner fender guard sometimes, and I was lowered on H&R Sport Springs (2" all-around) with Tokico D-Spec struts. I do have to note that I had the camber within OEM spec, -.5 in the front and -1.5 in the rear. If I went -1.0 in the front, it probably would've been fine.

I found that 225/45/16 work quite well all around, but you get less sidewall protection. I personally kind of like the beefiness of 225/50's.

This is an old picture of my tire setup. Rota Slipstreams 16 x 7 40+, 225/45 in front, 225/50 rear.
http://www.rasyran.com/rasy-ep3-resize.jpg

tlikethedrink
06-29-2010, 06:37 PM
thanks guys. so i should be ok on the rub... and if i ever do decide to drop, i would be ok unless its about a 2inch.

nice pics too. now my concern is looks. im dont want to look too too beefy on the stock ride hieght.

would 205s be too narrow for 7inch wheels? incase im not too fond of the beefy look...

jh604
06-29-2010, 06:54 PM
I'm on 215/50/16 slipstreams x7. I like the beefiness too. I have about 1 finger gap all around and no rubbing. Even with the IC piping sticking out of the fender liner

tlikethedrink
06-30-2010, 08:18 AM
I'm on 215/50/16 slipstreams x7. I like the beefiness too. I have about 1 finger gap all around and no rubbing. Even with the IC piping sticking out of the fender liner

drop? pics! thanks!

SinisterCivicSi
06-30-2010, 08:42 AM
IMO alot of it depends on WHAT your dropped on. if you have coilovers you should be fine... if your on lowering springs, you might have rub if you dont roll your fenders... depends on if you carry passengers alot, etc.

i am on progress coilovers dropped about 1.75-2 inches. i dont have rubbing issues unless i have a car full of people and i am going on an exit ramp or something, it might just slightly tap the fender well on a bump... other than that - no issues...


these are old pics but i am still rockin the same setup - just a little lower now than pictured here:

http://i13.photobucket.com/albums/a288/SinisterCivicSi/evensin/newlights2.jpg
http://i13.photobucket.com/albums/a288/SinisterCivicSi/evensin/newlights1.jpg

jh604
07-03-2010, 10:51 AM
drop? pics! thanks!

Dropped on Megan coilovers

The Front - http://img3.imageshack.us/img3/2649/img00081201007031038.jpg
Couldnt get pics with the IC piping but I hope this helps

The Rears - http://img576.imageshack.us/img576/7615/img00082201007031038.jpg

Alex857
07-07-2010, 07:03 PM
i had 225/50s on stock ex wheels stock height, no rubbing, also lowered 2 inches, no rubbing. i can provide pics if youd like

tlikethedrink
07-07-2010, 10:15 PM
i got my tires on. went with a falken 512 in 205 55. im pretty sure its the rim mainly- but they LOOK extra beefy. the orange lip INSIDE the rim make the rims look like 14s from a side view. angles are ok, you can see the tire start and the rim end in gm not orange...

http://i41.photobucket.com/albums/e285/aranciors/Si/rim1.jpg

kai-wun
10-29-2010, 10:02 AM
Bumping this thread.

Would 225/50R16 work okay on a 16x7 rim? Or too much bulge to be unsafe?

chiwhitesi
10-29-2010, 10:07 AM
im running a 225/50/16 @ stock height and it is perfectly fine even @ full compression

Aaron_in_MO
11-17-2010, 03:34 PM
Like what ryan02 said, you have to roll the back. When I had 225/50/16's in the front, they rubbed on the inner fender guard sometimes, and I was lowered on H&R Sport Springs (2" all-around) with Tokico D-Spec struts. I do have to note that I had the camber within OEM spec, -.5 in the front and -1.5 in the rear. If I went -1.0 in the front, it probably would've been fine.

I found that 225/45/16 work quite well all around, but you get less sidewall protection. I personally kind of like the beefiness of 225/50's.

This is an old picture of my tire setup. Rota Slipstreams 16 x 7 40+, 225/45 in front, 225/50 rear.
http://www.rasyran.com/rasy-ep3-resize.jpg

I actually like the look of this better than with 17s or 18s. Do the 225/45 rub in front, like the 225/50 did? I'd like to do a similar set-up, but with 225/45s all the way around, and if I could avoid rubbing or having to roll the fenders, that'd be great.

jjr007
11-23-2010, 04:25 AM
Like what ryan02 said, you have to roll the back. When I had 225/50/16's in the front, they rubbed on the inner fender guard sometimes, and I was lowered on H&R Sport Springs (2" all-around) with Tokico D-Spec struts. I do have to note that I had the camber within OEM spec, -.5 in the front and -1.5 in the rear. If I went -1.0 in the front, it probably would've been fine.

I found that 225/45/16 work quite well all around, but you get less sidewall protection. I personally kind of like the beefiness of 225/50's.

This is an old picture of my tire setup. Rota Slipstreams 16 x 7 40+, 225/45 in front, 225/50 rear.
http://www.rasyran.com/rasy-ep3-resize.jpg

Sweet looking ep you have there!

o2ep3
11-23-2010, 08:22 PM
i ran 225/45/16 not rolled and didnt have issues jjroo7 seen them on my daily wheels. how you been jjroo7 long time no see i been workin on a new set up for the track you still running with

.colin
11-23-2010, 09:02 PM
i just mounted up a set of 225/50 falken ziex 512s on the stock 04 wheels, no rubbing with mugen SS