megan midpipe with obx twin loop?

[kale's blue ep3]

anyone have it? or something similiar hows it sound?

[robotichatch]

if your running the a3 i would get the megan mid pipe and keep the stock axle back.

[kale's blue ep3]

why?

[urthworm]

I have the mugen twin loop with buddyclub race header (no cat) and it sounds fan-freaking-tastic! Doesnt even sound like a typical honda at all.. super quiet at idle and so good at wot.

Im not sure how the obx compares but i doubt it that much different. And i think robotichatch suggest just changing the midpipe is because its the most restrictive part of the exhaust.

[EPSU3]

I was going to use this set up but the stock axle back was free so I just went with that. It's nice in quiet but a little bit deeper.

[kale's blue ep3]

anyone? i think im going to give it a try

[kale's blue ep3]

the 2.5in or the 3in obx twinloop? any ideas

[robotichatch]

our stock axle backs are restrictive after 205hp i believe. so upgrading it is a bit unnecessary i think. but a twin loop would be sick :rockon:

[kale's blue ep3]

robot for the twin loop do you think 2.5in or 3in? thanks

[jri93]

no point in running a 3in axle back when the megan mid pipe is only 2.25in ... btw i have this exact setup with the obx raceheader sounds good, but like others said, the stock axleback is fine for the a3 and sounds good. i only got the twinloop after i installed the raceheader and it was way to raspy lol

[talonXracer]

The stock axle back is good but alot less than 200whp good, LOL

The loop mufflers produce THE greatest gains with the lowest sound output of ANY other muffler design produced.

You need no larger than 2.5" for the exhaust piping unless you desire non-stop harassment from the cops. In almost every case there would be significant drop in low end and mid range power and driveabililty with a 3" exhaust on a a3.

[kale's blue ep3]

so you think it would be raspy? or should i get a 2.25 twinloop mufler that matches the same piping size as my megan midpipe?

[urthworm]

Id go 2.5 if your planning on staying n/a.. its a good size and it wont be loud.

[kale's blue ep3]

I just dont want it to be raspy

[urthworm]

it wont be.. as long as you have a cat or resinator it will sound great.

[usedep3]

i had a 2.25" magnaflow midpipe with an obx 2.5" obx twinloop. i still had the stock header/cat at the time and thought it sounded great. i really miss that setup, but thank goodness i now have the mugen twinloop to keep me happy.

i would def recommend the megan midpipe w/ the obx twinloop. just be sure you know what you're getting yourself into. the obx is not of the highest quality. after a year you could start seeing some of the welds cracking.

[kale's blue ep3]

i know after awhile i want to do mugen twinloop with dcrh. but this setup will hold me off for awhile =]

thanks guys your a great help

[kale's blue ep3]

i have it on my car now it sounds great!

[gamma6]

i have it on my car now it sounds great!

Pics and vids plz

[kale's blue ep3]

ill post some this week

[gamma6]

ill post some this week

cool...

[BeaterEP]

i have it on my car now it sounds great!

You wind up going with the megan/obx setup?

[kale's blue ep3]

yes it sounds great But thinking of going race header soon. Just scared of being super raspy

[303EP]

Will the OBX twin loop with a 3 inch midpipe sound ricey?

[Manny Kid 15]

I had the twin loop with greddy evo 2 and it was really quiet

[Blah1219]

Will the OBX twin loop with a 3 inch midpipe sound ricey?

What are your mods? Turbo? K24a2? Why do you want a 3" midpipe?

[303EP]

What are your mods? Turbo? K24a2? Why do you want a 3" midpipe?

Going turbo this summer/spring, I dont want something too loud