jwdep3
03-29-2011, 09:09 PM
I did this about a week ago and i haven't seen a diy, so i thought I'd make one.
This is my first diy, so go easy on me
you will need:
8 wire taps
electrical tape
a really small screwdriver
2 sockets p# 33304-S30-003
2 bulbs p# 33303-S30-003
2 connectors p#04321-SH2-307
8 pigtails p# 04320-SP0-A00 or p#04320-SP0-B00
(I had a couple extra connectors and terminals, but you can go to the dealer and have them match it up)
http://i1197.photobucket.com/albums/aa426/ep3k20a31/parts.jpg
the brake/turn socket will transfer over with no problem. you will need to remove the connector from the top marker light and tap it to the reverse wire
http://i1197.photobucket.com/albums/aa426/ep3k20a31/step1.jpg
Remove the terminals from the top marker light
http://i1197.photobucket.com/albums/aa426/ep3k20a31/step2.jpg
you will need a really small screwdriver to lift the lock in the connector and remove the terminal
http://i1197.photobucket.com/albums/aa426/ep3k20a31/terminal.jpg
add terminals to the connector you removed
http://i1197.photobucket.com/albums/aa426/ep3k20a31/step3.jpg
and to the connector for the new socket
http://i1197.photobucket.com/albums/aa426/ep3k20a31/step4.jpg
Tap the new connector wires into the top marker light wires (it doesn't matter which way you tap the wires)
http://i1197.photobucket.com/albums/aa426/ep3k20a31/step5.jpg
Tap the the connector you reused into the reverse light wires (it doesn't matter which way you tap the wires)
http://i1197.photobucket.com/albums/aa426/ep3k20a31/step6.jpg
Everything should look like this
http://i1197.photobucket.com/albums/aa426/ep3k20a31/step7.jpg
Electrical tape all the wires separately so they wont short out
http://i1197.photobucket.com/albums/aa426/ep3k20a31/step8.jpg
and then install into your new (or should i say old) tail lights
http://i1197.photobucket.com/albums/aa426/ep3k20a31/step9.jpg
Do the other side and you're done :mcool:
http://i1197.photobucket.com/albums/aa426/ep3k20a31/done.jpg
hope this helps out all the people that want to do this. if i left out anything out please tell me.
This is my first diy, so go easy on me
you will need:
8 wire taps
electrical tape
a really small screwdriver
2 sockets p# 33304-S30-003
2 bulbs p# 33303-S30-003
2 connectors p#04321-SH2-307
8 pigtails p# 04320-SP0-A00 or p#04320-SP0-B00
(I had a couple extra connectors and terminals, but you can go to the dealer and have them match it up)
http://i1197.photobucket.com/albums/aa426/ep3k20a31/parts.jpg
the brake/turn socket will transfer over with no problem. you will need to remove the connector from the top marker light and tap it to the reverse wire
http://i1197.photobucket.com/albums/aa426/ep3k20a31/step1.jpg
Remove the terminals from the top marker light
http://i1197.photobucket.com/albums/aa426/ep3k20a31/step2.jpg
you will need a really small screwdriver to lift the lock in the connector and remove the terminal
http://i1197.photobucket.com/albums/aa426/ep3k20a31/terminal.jpg
add terminals to the connector you removed
http://i1197.photobucket.com/albums/aa426/ep3k20a31/step3.jpg
and to the connector for the new socket
http://i1197.photobucket.com/albums/aa426/ep3k20a31/step4.jpg
Tap the new connector wires into the top marker light wires (it doesn't matter which way you tap the wires)
http://i1197.photobucket.com/albums/aa426/ep3k20a31/step5.jpg
Tap the the connector you reused into the reverse light wires (it doesn't matter which way you tap the wires)
http://i1197.photobucket.com/albums/aa426/ep3k20a31/step6.jpg
Everything should look like this
http://i1197.photobucket.com/albums/aa426/ep3k20a31/step7.jpg
Electrical tape all the wires separately so they wont short out
http://i1197.photobucket.com/albums/aa426/ep3k20a31/step8.jpg
and then install into your new (or should i say old) tail lights
http://i1197.photobucket.com/albums/aa426/ep3k20a31/step9.jpg
Do the other side and you're done :mcool:
http://i1197.photobucket.com/albums/aa426/ep3k20a31/done.jpg
hope this helps out all the people that want to do this. if i left out anything out please tell me.