View Full Version : intake with RBC
k3rry
04-24-2011, 01:24 AM
what intake are you guys running with the rbc intake mani? i have a injen CAI and had a close call with hydrolock the other day, and i dont wana buy another motor. what intake do you have to mod to fit the filter behind the headlight?? im going to relocate the battery
abstract
04-24-2011, 02:16 AM
might as well get the password intake/battery relocate
Tortoise
04-24-2011, 05:42 AM
Thats why i grabbed the pwjdm powerchamber. Wanted better gains then an sri but still not risk hydrolocking!
talonXracer
04-24-2011, 06:40 AM
The components to create a custom SRI/CAI with a relocated battery are available at any AutoZone or parts stores. Simply look at my signature......
k3rry
04-24-2011, 07:41 AM
The components to create a custom SRI/CAI with a relocated battery are available at any AutoZone or parts stores. Simply look at my signature......
So your really just need one hole for the sensor? And but a breather on the other two?
k3rry
04-24-2011, 07:41 AM
Thats why i grabbed the pwjdm powerchamber. Wanted better gains then an sri but still not risk hydrolocking!
It works fine with the rbc? Have any pics?
RHCP0801
04-24-2011, 08:23 AM
mine is run the same way as talon
k3rry
04-24-2011, 09:55 AM
mine is run the same way as talon
What did you use? And what did you do with the two hoses that connects to the intake?
RHCP0801
04-24-2011, 10:06 AM
the iat sensor i ran to one of the grommets above the rad behind the grille so it still gets the ambient temp and wont cause any problems. The one that runs from valve cover i just put a filter on the end of the vc, my intake pipe is custom made and doesnt have the holes for either one
02CivicSI-VTEC
04-24-2011, 10:23 PM
i ran a injen CAI when I had my RBC IM
talonXracer
04-25-2011, 05:53 AM
To fit the IAT into the intake tract you simply drill a hole in the tubing, insert a grommet and then push the probe into the grommet, just like EVERY CAI/SRI ever produced for any application!
The larger tube, which connects to the VC breather, does not have to connect to the intake, a seperate filter can be attached, just make sure it isnt directly on the VC, but after the heater section and approx 4-6" of additional tubing.
k3rry
04-25-2011, 09:31 AM
To fit the IAT into the intake tract you simply drill a hole in the tubing, insert a grommet and then push the probe into the grommet, just like EVERY CAI/SRI ever produced for any application!
The larger tube, which connects to the VC breather, does not have to connect to the intake, a seperate filter can be attached, just make sure it isnt directly on the VC, but after the heater section and approx 4-6" of additional tubing.
the tube after the heater seciton can hang anywhere?
talonXracer
04-25-2011, 10:29 AM
Here is my set-up
http://i54.photobucket.com/albums/g96/talonxracer/IMG_0930-1.jpg
k3rry
04-25-2011, 08:39 PM
have pictures of the other hose??
RHCP0801
04-25-2011, 08:48 PM
what other hose
k3rry
04-26-2011, 01:35 AM
what other hose
theres two hoses that connects to the intake and a sensor
j0000stin
04-26-2011, 01:50 AM
Here is my set-up
http://i54.photobucket.com/albums/g96/talonxracer/IMG_0930-1.jpg
it's a good thing you dont live in CA haha
Powered by vBulletin® Version 4.2.3 Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.