cyllarus
10-20-2013, 06:57 PM
Hey everyone.
I've got my hands on a Z3 tranny and am going through the process of fitting it to my EP3.
I am using Papi's write up on how to use a dakota digital to convert the high frequency Z3 speedo signal to the low frequency signal needed by the ECU.
http://forums.clubep3.com/showthread.php?t=584291&highlight=dakota+digital
But I am a bit confused by his wiring diagram, he says the input signal gets wired to the old speedo, and the output gets wired to the NEW speedo? Why would i even have the old speedo in the engine bay?
Cant I just splice the new VSS into my existing harness, then wire the Daktoa digital in between the VSS and the ECU on the signal wire?
Also: I am swapping a RSX Shift Mechanism according to this thread:
http://www.k20a.org/forum/showthread.php?t=40933
One update here that everyone might find interesting: The above thread says you can only get 3 of the 4 mounting bolts to work when you mount the RSX shifter to the Z3 case, and one of the bolts has to have a hole drilled / tapped for it to mount. ( If you read through the above thread you will see a picture of the 3 bolts mounted, and one open spot with no bolt in it.
With some careful inspection I found that the case is actually setup to drill / tap the 4th bolt too. Below is a picture of the Z3 case with 2 bolt holes drilled to accept the RSX shift mechanism
http://i594.photobucket.com/albums/tt22/GargleSpam/2013-10-20_15-39-17_4071_zpsca14f9e5.jpg
In this photo, the hole on the upper left, and the lower left were drilled and tapped by me. The hole that is 1 down on the left, and on the bottom in the middle are the factory bolt holes.
And the mounted Shifter, note how my picture differs from the one in the above thread, Look at the upper left of the shifter, and the fact that I DO have a bolt there.
http://i594.photobucket.com/albums/tt22/GargleSpam/2013-10-20_21-49-30_927_zps5d47c139.jpg
I've got my hands on a Z3 tranny and am going through the process of fitting it to my EP3.
I am using Papi's write up on how to use a dakota digital to convert the high frequency Z3 speedo signal to the low frequency signal needed by the ECU.
http://forums.clubep3.com/showthread.php?t=584291&highlight=dakota+digital
But I am a bit confused by his wiring diagram, he says the input signal gets wired to the old speedo, and the output gets wired to the NEW speedo? Why would i even have the old speedo in the engine bay?
Cant I just splice the new VSS into my existing harness, then wire the Daktoa digital in between the VSS and the ECU on the signal wire?
Also: I am swapping a RSX Shift Mechanism according to this thread:
http://www.k20a.org/forum/showthread.php?t=40933
One update here that everyone might find interesting: The above thread says you can only get 3 of the 4 mounting bolts to work when you mount the RSX shifter to the Z3 case, and one of the bolts has to have a hole drilled / tapped for it to mount. ( If you read through the above thread you will see a picture of the 3 bolts mounted, and one open spot with no bolt in it.
With some careful inspection I found that the case is actually setup to drill / tap the 4th bolt too. Below is a picture of the Z3 case with 2 bolt holes drilled to accept the RSX shift mechanism
http://i594.photobucket.com/albums/tt22/GargleSpam/2013-10-20_15-39-17_4071_zpsca14f9e5.jpg
In this photo, the hole on the upper left, and the lower left were drilled and tapped by me. The hole that is 1 down on the left, and on the bottom in the middle are the factory bolt holes.
And the mounted Shifter, note how my picture differs from the one in the above thread, Look at the upper left of the shifter, and the fact that I DO have a bolt there.
http://i594.photobucket.com/albums/tt22/GargleSpam/2013-10-20_21-49-30_927_zps5d47c139.jpg