PDA

View Full Version : em2 ball joint replaces our stock ep3 ball joint.



Eddie Murphy
12-23-2014, 02:54 PM
OK after a bit of research I found out that you can replace your ball joints with OEM parts, without buying the whole knuckle. EM2 ball joints are the same, so just buy OEM Honda em2 ball joints. They will also work for all RSX model years 02-04, for you 5 lug swap guys. Part# 51220-s5a-305.
JOINT, FR. BALL (LOWER) - Honda (51220-S5A-305)
(http://www.afhparts.com/oe-honda/51220s5a305?search_str=51220-s5a-305) Part can be found as reference #2 in illustration.
And the changeable dust boot is #3. The little rubber boots are a maintenance item and should be changed as they wear out... Just like your oil, just like your brakes! If your joint is still good, and the boot is not... Why not just change it before things get worse? It is a $4 part from the Honda dealership.

http://s3.amazonaws.com/rparts-illustrations/strapr1/8d6060103c10417eddcad1cf76ab9b05/8e89279000cc519f7e0f8aa9a1ca8bbe.png

I also highly advise looking up the little special shop tool that honda makes to seat the boot onto its place. Ohh yeah... Heres the part number on the tool... 07965-SA50500 (http://www.afhparts.com/oe-honda/07965sa50500)
Tie Rod Boot: Service and Repair
Tie-rod Ball Joint Boot Replacement (http://workshop-manuals.com/acura/mdx/v6-3.7l/steering_and_suspension/steering/tie_rod/tie_rod_boot/component_information/service_and_repair/)

27rocks
12-28-2014, 09:29 AM
Good stuff!

Her-Name's-Ally
12-29-2014, 02:31 PM
Really Great info eddie boy.

Eddie Murphy
01-03-2015, 09:02 AM
https://scontent-b-atl.xx.fbcdn.net/hphotos-xpa1/v/t1.0-9/10898288_10204327604443246_7463891688610823907_n.j pg?oh=14df04473113263da6f8cacaac02792f&oe=55267423

Euro-Yellow-Ep3
02-03-2015, 06:15 PM
Eddie FTW

Eddie Murphy
02-13-2015, 06:56 PM
http://maiden-world.com/images/wallpaper/Eddie_Mummy_1024.jpg

BeaterEP
10-16-2015, 05:35 PM
Droppin' questions on the forumz tooooooo! :mbiggrin:


Back from the dead motherfuckers!!!!!

...me and this post, both LOL

Eddie Murphy have you done the EM2 ball joint replacement?
Getting ready to tear the front suspension apart and replace the lower ball joints, already got the parts, but there's no retaining ring.
Are these a straight press fit?
I know the OEM EP3 joints are supposedly factory installed using heat on the knuckle, cold on the ball joint, and epoxy in between.
Will these just press fit and ride?

Eddie Murphy
10-16-2015, 06:45 PM
Guys have been doing this forever with the em2 ball joint... they all say the em2 presses in.
http://www.7thgenhonda.com/forum/showthread.php?t=25332
http://www.civicforums.com/forums/119-suspension/308090-7th-gen-ball-joint-diy.html

BeaterEP
10-16-2015, 09:00 PM
:thumbu:

Eddie Murphy
06-14-2017, 06:23 AM
I replaced my driver side with Sankei 555(JAPAN) like 4 years ago, all good https://www.facebook.com/images/emoji.php/v9/z73/1/16/f0000.png
https://www.carid.com/sankei-555/ball-joint-mpn-w0133-1632134-snk.html?singleid=7659396&url=3598711 (https://l.facebook.com/l.php?u=https%3A%2F%2Fwww.carid.com%2Fsankei-555%2Fball-joint-mpn-w0133-1632134-snk.html%3Fsingleid%3D7659396%26url%3D3598711&h=ATNaSJ_5_qfG-ZBYygTmpTIBnHZJuPdGKV9GLtDpCPYBsrFAgAQuU9n_y-U3gJEIaioCFHjznRUku65ZcPfDFiGjVf23b5uU-gzfmkj1SMszsPR0DzWAGLwKAjLC5bNxzZSIv1LAq4-vGCHihh7zvdbJtg)

vtecDave
08-29-2017, 06:35 PM
Thanks for this info. I recently got the car bug again and when under her the other weekend I noticed that everything was shot. So neglected. 😣
Tops and bottoms, L&R all split and drying out... including sway bar endlinks. Assuming inner tie rods need replacing also. Lots of wrench time ahead.