how do you install? batery and what else!:mredface:
Printable View
how do you install? batery and what else!:mredface:
http://www.civicforums.com/forums/11...t-install.html
Not our car, but a person who knows EPs well might be able to customize that mod to ours. *patiently waiting*
wow, I cant believe this DIY was lost, I thought it was older. I have mine done. Give me a hour and I can at least have pics up.
dont worry guys there is one on k-series
http://www.k-series.com/tech_document.php?id=25
Posted with some ganked info from k-series.com, but without an attempt to sell you a product you can make yourself.
EP Ground Wire Installation
What you need:
- Socket Wrench
- 10mm Socket
- 12mm Socket
- Socket Extension
- Zip Ties
- 4-8g wire- Oxygen Free, sleeved in color of choice. (I went with Red)
- Gold plated terminal caps
- Heat shrink wrap- color of choice
- Wire cutters
- Wire strippers capable of stripping insulation on 4-8g wire
- Wire crimpers capable of crimping connectors on 4-8g wire
- Heat Gun or small lighter
Alternatively, you can by the "JDM grounding kit" from Ebay which will come with all the wires pre-cut to appropriate lengths, crimped, terminated, wrapped and ready to go. It'll also come with this nifty Bracket that helps keep all the wires neatly arranged - cost is around $20 shipped.
http://img.photobucket.com/albums/v2...dingKit009.jpg
Procedure:
My engine bay!... yes I know its dirty :mangel:
http://img.photobucket.com/albums/v2...dingKit004.jpg
Grounding Points
1. Negative to Battery tie down.http://img.photobucket.com/albums/v2...dingKit008.jpg
2. Negative to strut tower ground http://img.photobucket.com/albums/v2...dingKit007.jpg
3. Negative to nut on intake manifold. http://img.photobucket.com/albums/v2...dingKit010.jpg
4. Intake manifold to ground by pulleys. http://img.photobucket.com/albums/v2...dingKit011.jpg
5. Ground by pulleys to valve cover.
http://img.photobucket.com/albums/v2...ND_WIRES-9.jpg
Posted with respect to k-series.com. Mine is currently off bc I was installing a header recently and it was in the way.
1. Start by checking the lengths of your wires (if you bought it yourself) from Negative Battery terminal to grounding points 1, 2, and 3
2. Then measure a length of wire from grounding point 3 -> 4, then from 4 -> 5. Remember to route the wires away from engine heat by tucking them under the frame around the headlamps, and along the back of the passenger- side strut tower.
3. Once all lengths of wire have been measured and Identified, terminate each end in terminal caps and heat shrink wrap the connections.
http://img.photobucket.com/albums/v2...dingKit003.jpg
Setting the Grounds
1. Start by loosening the negative battery terminal (10mm)
2. Add ground wires for locations 1, 2 and 3 to the negative battery terminal and tighten it down.
3. Connect Wire 1 to the battery tie down.
4. Connect Wire 2 to the Strut Tower Grounding point
5. Connect Wire 3 to the intake manifold bolt (10mm), but dont tighten the bolt down yet.
6. Run Wire 4 from the intake manifold to the Motor Mount Ground near the pulleys (10mm). Tighten the manifold bolt down, but do not tighten Motor Mount Ground Bolt yet. Make sure you tuck it underneath the frame and secure with zip ties.
7. Run the last wire from the Motor Mount ground near the pulley to rear of the valve cover. Tighten down both bolts. Make sure you run the wire along a path behind the engine to avoid heat and secure with zip ties.
8. As the last step, remove the IM Cover and locate the Fuel Rail ground (Yellow Nut) http://img.photobucket.com/albums/v2...dingKit013.jpg
Re-locate this ground to the valve cover as per Hondata's recommendations for proper ECU protection.
http://img.photobucket.com/albums/v2...dingKit014.jpg
This is likely unnecessary if you do not have Kpro, but is a good practice while you are working on this project.
9. All Done!
http://img.photobucket.com/albums/v2...dingKit006.jpg
:smokin::bathbaby: Take a rest and clean yourself up! :mbiggrin: Enjoy less power spikes and smoother Idle operation. When I finished this, my idle went from 1000-1100 to 800 steady.
All Done! :mbiggrin:
Could a Mod please change the title to remove the ?? and clean up the posts before the DIY?
Thank you!
thnx man! :mwink: i <3 ephatch
i changed the title a little bit as requested.
great info and write up.
Sic! =)
Any user comments would be nice too =)
whoa thanks for the DIY. those pictures of the exact mounting points are AWES-FUCKING-SOME!
i'm gonna do this really soon now.