Five Lug - Installed!

[cease]

i like that

[BlackJDMep]

is the rsx bolt pattern the same as a 99 prelude?

[02TafWhtSi]

Those wheels look awesome on our EP's! Can't wait to see yours CPU ;)

[Makross]

damn those look good

[!@#$%]

those wheels look ok, but really work with the rsx. I think it has to do with the front end. hmm, what would an rsx front end look like on an si body with ctr wing? lets get a photochop!

[StrangeShadow]

those wheels look ok, but really work with the rsx. I think it has to do with the front end. hmm, what would an rsx front end look like on an si body with ctr wing? lets get a photochop!

there're a lot in the photochop forum. =)
-where did you get all your parts? someone have a totaled rsx?

[cpu519]

I got the parts from a Type S owner who installed the JDM Integra Type R Brembos. Check clubrsx.com, RSX owners are more likely to sell their parts cheaper than a junkyard because they need to get rid of them.

[CivicSiR4U2NV]

Hey do you think you could post detailed info of whats need to do this plz. I want to do this but i am unshure of whats exactly needed.

[cpu519]

From the diagram below, here are the parts needed for the rear:

#3, BEARING ASSY., RR. 2 needed
#37, BOLT, WHEEL , 10 needed
#5, DISK, RR. BRAKE, 2 needed
#4, CAP, HUB UNIT, 2 needed
#38, NUT, SPINDLE, 2 needed (Manual says to replace, not absolutely necessary)

Check this Acura parts dealer for prices. It's not cheap when you have to buy the parts from the dealer though.

[CivicSiR4U2NV]

Originally posted by cpu519
From the diagram below, here are the parts needed for the rear:

#3, BEARING ASSY., RR. 2 needed
#37, BOLT, WHEEL , 10 needed
#5, DISK, RR. BRAKE, 2 needed
#4, CAP, HUB UNIT, 2 needed
#38, NUT, SPINDLE, 2 needed (Manual says to replace, not absolutely necessary)

Check this Acura parts dealer for prices. It's not cheap if you have to get the parts from the dealer.



I'll list the front parts needed shortly...

Thanx now all i need is the front then its of the my acura dealer to get the parts. :)

[StrangeShadow]

RSX owners are more likely to sell their parts cheaper than a junkyard because they need to get rid of them.

sweet, thanks, must say this is one of the most educational threads I've seen in a while :thumbsup:

[Mr.02BlackSIguY]

with the rsx 5 lug conversion like this. will the jdm CTR 17 inch rims fit? i heard it wont because its a different offset that the CTR ep3 5 lugs. any one? i would love to go junkyeard and get and rsx five lug because it would be cheaper than getting the actual ep3 CTR 5 lug. gosh.. things i do for jdm hhehe.

[cpu519]

The JDM CTR wheels are 17 x 7", probably a 45mm offset, and the bolt pattern is 5 x 114.3. The bolt pattern is the same, so they will fit with no problem.

[cpu519]

Here are the parts needed for the front, starting with the knuckles:

#2 and 3, KNUCKLE, R. FR., KNUCKLE, L. FR., right and left side
#4, BOOT, BALL DUST, 2 needed
#19, NUT, ARM (12MM), 2 needed
#20, CLIP, ARM (UPPER), 2 needed

Prices can be found here

Double check with the dealer on all parts requiured.

[cpu519]

All of these parts are required, left and right side. You'll definitely save money by getting the Wilwood kit for the Type S instead of brand new Acura rotors and calipers. Calipers that fit the S2000 also fit, that opens up more possibilities. The hub parts are pressed into the knuckles, so take that into consideration. You'll need the Type S front brake hoses also.