Close

Page 2 of 4 FirstFirst 1234 LastLast
Results 16 to 30 of 51
  1. #16
    elitist jerk weltall's Avatar
    Join Date
    Feb 2004
    Location
    no where
    Posts
    3,641
    what voltage ia the knock level at?

    true knock happens around 1.25 vdc

    lower than that will still register but it can be attributed to mechanical noise
    i once had a 592whp ep on pump gas, i sold it and bought a Z
    (heed my advice i know what im doing)

  2. #17
    slow & quiet again 4angrybadgers's Avatar
    Join Date
    Dec 2006
    Location
    Hattiesburg, MS
    Posts
    1,189
    I've been all over the datalogs for 10 minutes and can't figure out what you're hinting at, Jpax.

    BTW, I don't see 6th gear in the datalogs, just up to 5th.

  3. #18
    Site Sponsor 02EP3SI's Avatar
    Join Date
    Apr 2004
    Location
    Cincinnati
    Posts
    451
    i mostly notice the af cmd is all weird from 4600 to 6900 on log 2. Also notices the knock thresh is at zero the whole time.

  4. #19
    ΜΟΛΩΝ ΛΑΒΕ talonXracer's Avatar
    Join Date
    Apr 2004
    Location
    Catskill Mtns
    Posts
    9,252
    Quote Originally Posted by Jpax View Post
    yeah the owner said it was a 5 speed but kpro says 6th speed, unless they threw it in reverse while furll throttle then I would go with K pro s readings lol

    If the gear ratios are incorrect in the gear comp tab, you will have some abnormal indications,,goofy A/F that doesnt seem to correct right.
    ALL advice issued with this "Disclaimer"
    Tim "the Toolman" Taylor is my HERO ! ! !

    "Labor Unions are Domestic Terrorist orgainizations"

  5. #20
    I.C.U.P. FoReVaPmP's Avatar
    Join Date
    Jun 2004
    Posts
    5,229

  6. #21
    elitist jerk weltall's Avatar
    Join Date
    Feb 2004
    Location
    no where
    Posts
    3,641
    does this car have an rbc???
    i once had a 592whp ep on pump gas, i sold it and bought a Z
    (heed my advice i know what im doing)

  7. #22
    ROAR LIONS! SyckSiR's Avatar
    Join Date
    Aug 2004
    Location
    Abbotsford, BC, Canada
    Posts
    1,583
    Quote Originally Posted by 02EP3SI View Post
    i mostly notice the af cmd is all weird from 4600 to 6900 on log 2. Also notices the knock thresh is at zero the whole time.
    my knock thresh stays at zero all the time too.....

  8. #23
    Registered User Lenus's Avatar
    Join Date
    Apr 2008
    Location
    HN
    Posts
    78
    Quote Originally Posted by SyckSiR View Post
    my knock thresh stays at zero all the time too.....
    same here

  9. #24
    432hp 360tq @14lbs Civic5lug's Avatar
    Join Date
    Jan 2005
    Location
    NJ
    Posts
    2,694
    Quote Originally Posted by plainol2k2si View Post
    Besides what those guys mentioned, I'm not sure If i'm keen enough to find anything else.

    If you get a moment to answer this side question though; ive been dealing with a very stubborn TSX .kal. Ive got the k24a2 with sri, and nothing else, but on the stock tsx .kal ive got around 27 knocks right around 4600(vtec)-6500. I added a little bit of fuel to that whole area. But I had to subtract almost 5-6 degrees of ignition to get rid of all the knocks. Is that really strange?
    post a log

  10. #25
    elitist jerk weltall's Avatar
    Join Date
    Feb 2004
    Location
    no where
    Posts
    3,641
    hell i have a loose zip tie that whacks the fan when it kicks on and registers knock
    i once had a 592whp ep on pump gas, i sold it and bought a Z
    (heed my advice i know what im doing)

  11. #26
    slow & quiet again 4angrybadgers's Avatar
    Join Date
    Dec 2006
    Location
    Hattiesburg, MS
    Posts
    1,189
    Quote Originally Posted by weltall View Post
    hell i have a loose zip tie that whacks the fan when it kicks on and registers knock
    I have a dying front strut that pops and shows as knock when I'm cruising on the highway (perfectly flat road). Scared me until I realized it wasn't real knock...

  12. #27
    elitist jerk weltall's Avatar
    Join Date
    Feb 2004
    Location
    no where
    Posts
    3,641
    yeah i know what knock sounds like (jar o'marbles) it was freaking me out untill i got in the garage with the turbo timer on and the fan kicked on and heard a buzzing sound then i went and looked at the CEL and it was going apeshit

    only happens with the fan on = not worried about it
    i once had a 592whp ep on pump gas, i sold it and bought a Z
    (heed my advice i know what im doing)

  13. #28
    My civic is go chubbychu's Avatar
    Join Date
    Feb 2003
    Location
    Downtown San Jose/Redding
    Posts
    3,545
    Quote Originally Posted by civic5lug View Post
    post a log

    would you guys need a datalog with .kal to take a look at it?
    Formerly known as Plainol2k2si

  14. #29
    Ep whaaa? Jpax's Avatar
    Join Date
    Sep 2002
    Location
    Edmonds, Washington, United States
    Posts
    4,108
    Ok from the owner its a 5 speed now, Why kpro showed a 6th gear is weird.

  15. #30
    Ep whaaa? Jpax's Avatar
    Join Date
    Sep 2002
    Location
    Edmonds, Washington, United States
    Posts
    4,108
    the ignition at low RPM 2200~2600 has a nasty dip, and knock occured there, besides the obvious Lean issuses. the cams are only going to 26 degreees, the map says 40

    engine is K24A4 so obviously its not going to rotate past 30 becuase the VTC phyusicaly can't do it.
    Last edited by Jpax; 04-21-2008 at 10:32 PM.

Page 2 of 4 FirstFirst 1234 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •