info needed for rear JDM lip install

[72chevel]

It seems info for lip install was deleted anyone have partnumber info for the clips that install the rear lip to the bumper? also there seems to be some kind of clip/nut that needs to go in there to fasten the lip to the bumper.

[Siborg]

I had all the part #'s saved in my pm's:boom:

[JunSIR]

i need that info too please pm me if anyone finds it!!

[72chevel]

So I got a quote from the UK the way it looks I need 32 and 35. IDK there is more to it than this quote shows there is like 2 more places on each end where it looks like there is a connection.

[05silversi]

Yeah, that was my thread with all the part numbers.

You are correct, will need 4 each of #s 32 and 35, these are the only ones that need to be sourced from Japan or UK. Also will Need:

# --- part number ----- desc ---- qty
31 -- 90126-SA7-000 -- screw -- 2
38 -- 90345-S04-000 -- clipnut -- 2
36 -- 90305-SH3-000 -- clipnut -- 2
39 -- 90501-SM4-003 -- bolt ---- 2

All available from US Honda. Everything else will reuse your factory parts.

[72chevel]

great, thanks for the info!

[RedSiBaron]

if you want to know what I did on mine, i used the same screws for the lip that they use on the mudflaps, and there should be atleast one back there, i used the pop in clips that you would use in the fender liner for the 2 underneath, and i used the pop in clips that came with my type r side skirts and i pushed them through the holes in the bumper, then pulled the teeth out...it made it so they pulled the lip on very tight, i highly suggest this...

[rd02SiR]

This thread has been a great help with my jdm side skirts.

Do I need that rubber strip that goes along the top of the skirt? Mines all fubar, so i was thinking if using the 3m double sided foam tape.

And for those with an 02/03, did you have to drill under the car to bolt up the under support brackets?

[EPtyper]

This thread has been a great help with my jdm side skirts.

Do I need that rubber strip that goes along the top of the skirt? Mines all fubar, so i was thinking if using the 3m double sided foam tape.

I used 3M Super Weatherstrip & Gasket Adhesive on the rubber strip. I got it @ AutoZone. I think it would be a good idea to keep it on there. Help evacuate water and from scratches forming from the parts vibrating.

Oh, and I have always been jealous you guys got Milano Red as an option.

[rd02SiR]

So on my 02, there are pre drilled holes under the car, exactly where the under body support goes. Then use push clips.

[usedep3]

This thread has been a great help with my jdm side skirts.

Do I need that rubber strip that goes along the top of the skirt? Mines all fubar, so i was thinking if using the 3m double sided foam tape.

And for those with an 02/03, did you have to drill under the car to bolt up the under support brackets?

So on my 02, there are pre drilled holes under the car, exactly where the under body support goes. Then use push clips.

so you do have predrilled holes underneath your ep3? i always thought the 02/03 usdm/cdm ep3 never came with those holes.

also, you dont need to replace that rubber gasket on the sideskirt. most people run the skirts without them.

[rd02SiR]

Yup I have 3 predrilled holes, right where the brackets go under. I guess it's essentially the same chassis, so it would the same holes. I also found larger holes under there as well. Ones with rubber plugs in them, like 3-4 at least per side.

[RedSiBaron]

Yup I have 3 predrilled holes, right where the brackets go under. I guess it's essentially the same chassis, so it would the same holes. I also found larger holes under there as well. Ones with rubber plugs in them, like 3-4 at least per side.

the chassis is the exact same, the only difference is the rear rebar mount points...thats all i have found to be different between the usdm and edm chassis...add in the RHD bulkhead for ukdm and jdm chassis...they all have "ep3" on them for a reason...we have a type r chassis, we are just missing the type r bits that came bolted on it in other countries