Close

Page 1 of 7 123 ... LastLast
Results 1 to 15 of 98
  1. #1
    Moderator=>PM 4 Help MugenReplica's Avatar
    Join Date
    Aug 2004
    Location
    Good question...
    Posts
    2,424

    Share your Kpro, Emanage, AEM EMS, etc. tune and setup here....

    If you have a tune and want to share it with the rest of Ephatch. Please post it here as an attachment so current and future Ephatchers can use it. Make sure to post your setup and the mods associated too. Thank you!

    NOTE---- ephatch or the members posting the calibrations cannot and will not assume any responsibility for any damage incurred on your engine
    *remember no two engines are alike and where one cal may work awsome on one setup it may not work correctly on an identical one*

    please post in this format to help those decide they want to try it before downloading
    engine type (stock or built please be specific on internals)
    list of modifications (again be specific)
    FI include boost level (s/c post pulley size)
    tranny type and mods to it as well
    injector size (very important)
    fuel system type (return or stock please include pump size)
    NOTES - any issues members should know about

    **if you do post who tuned it please keep in mind that some tuners get upset when there tunes are posted publically***
    keep this in mind as when tuners get upset about it they actually start to lock the ecu after tuning not allowing the tune to be leaked on the net


    here is a fine example on how to post it up

    Quote Originally Posted by 4angrybadgers View Post
    k20a3 (stock)
    JRSC, 3.8" pulley
    AEM Type-S (3") CAI
    DCRH (EP-specific)
    Skunk2 Megapower 70mm exhaust (no silencer)

    Tuned by "Tampa Mike" (aka Mike Amerson).
    NOTE: Deceleration on throttle closing is sharper than it was pre-tune (running the base JRSC-R map). I'm still tweaking it, and if I figure out the issue I'll post the new tune.
    Last edited by weltall; 05-01-2008 at 07:10 PM.

  2. #2
    360+barpsin=death! davisj3537's Avatar
    Join Date
    Apr 2008
    Location
    DFW
    Posts
    654
    Kpro
    K24a1
    Too many mods to list
    50 trim cybernation setup @ 10lbs of boost
    301whp 300wtq
    Tuned @ 50 degrees F
    Stoopid Tuned
    davis K24 EP3T toon.kal
    Last edited by davisj3537; 05-07-2008 at 08:47 AM.

  3. #3
    slow & quiet again 4angrybadgers's Avatar
    Join Date
    Dec 2006
    Location
    Hattiesburg, MS
    Posts
    1,189
    k20a3 (stock)
    JRSC, 3.8" pulley
    AEM Type-S (3") CAI
    DCRH (EP-specific)
    Skunk2 Megapower 70mm exhaust (no silencer)

    Tuned by "Tampa Mike" (aka Mike Amerson).
    211/165 on a Mustang dyno. Boost peaked around 8.5psi.
    NOTE: Deceleration on throttle closing is sharper than it was pre-tune (running the base JRSC-R map). I'm still tweaking it, and if I figure out the issue I'll post the new tune.
    Attached Files Attached Files
    Last edited by 4angrybadgers; 05-07-2008 at 08:51 AM. Reason: added final dyno numbers

  4. #4
    Registered User beechstreet's Avatar
    Join Date
    Jan 2004
    Location
    209
    Posts
    1,415
    k20a3 (stock internals)
    JRSC, 3.8" pulley, 440 injectors
    AEM V2
    Megan shorty 4-1
    OEM Cat
    Comptech 2.5" catback
    Tuned by Jei @ BlackTrax. Partial and WOT tunes. 9.5 PSI
    204WHP, 160WTRQ
    Attached Files Attached Files

  5. #5
    Moderator=>PM 4 Help MugenReplica's Avatar
    Join Date
    Aug 2004
    Location
    Good question...
    Posts
    2,424
    Found this one while looking online for a tune for a CAI/RH/E kal.

    k20a3 (stock internals)
    310cc injectors
    AEM CAI
    DCRH
    02-04 Type-S piping
    Canister style muffler
    PRB intake manifold and throttle body

    Originally on a Base RSX but now obviously has a PRB intake manifold.
    Attached Files Attached Files

  6. #6
    I'm playin w/ my Wii LaoKidd2k's Avatar
    Join Date
    Apr 2008
    Location
    silver spring, md
    Posts
    292
    k20z1head/a3block/mugen head gasket
    JRSC-R 4.0"pulley
    650cc
    injen cai
    jrrh
    greddy evo2

    k20a2-rsx-650cc-jrsc-5psi-markstune.kal

  7. #7
    Work in progress Mr_Safeway's Avatar
    Join Date
    Apr 2008
    Location
    Kent, WA
    Posts
    480
    anyone have a good k24a2 map?

  8. #8
    Registered User
    Join Date
    Feb 2009
    Location
    Dansville, MI
    Posts
    12

    basic ep3

    Hey everybody,
    just wanted to post my calibration and a couple 3rd gear pulls i did last nite. would appreciate some tuning help.
    already posted on hondata with no responses.
    Attached Files Attached Files

  9. #9
    ephatch member
    Join Date
    Apr 2008
    Location
    Chicago Area
    Posts
    1,240
    Quote Originally Posted by FlopMeister13 View Post
    Hey everybody,
    just wanted to post my calibration and a couple 3rd gear pulls i did last nite. would appreciate some tuning help.
    already posted on hondata with no responses.
    what are your mods?

  10. #10
    Registered User
    Join Date
    Feb 2009
    Location
    Dansville, MI
    Posts
    12
    Quote Originally Posted by AUTiger View Post
    what are your mods?
    dc sports short ram
    dc race header

    other cosmetic mods...

    i don't have enuf room in my que to load the datalogs. let me know of a way i could post them another way.

  11. #11
    Registered User
    Join Date
    Jul 2008
    Location
    AL
    Posts
    238
    JRSC
    K-pro
    3.8 Pulley (Making 8.5psi and drops after 7k)
    RC 440s
    AEM CAI (EP3 Specific - 2.5" Diameter)
    JRRH
    Tanabe Exhuast
    No cat (Exhaust is 2.3' all the way back)
    New 62" belt with Jmercado modded Auto Tensioner
    NGK 7 Iridium Plugs
    CC Stg 4 Clutch/Lightweight Flywheel

    http://rapidshare.com/files/42586190..._Sam_Oct13.kal

  12. #12
    Registered User VIZHUNZ02SI's Avatar
    Join Date
    Aug 2003
    Location
    Tampa Palms, FL
    Posts
    742
    anything for vtec killer kal. on a k24a1 please and thank you

  13. #13
    ephatch member
    Join Date
    Apr 2008
    Location
    Chicago Area
    Posts
    1,240
    hit up 1gr8ep3, I think he is running one.

  14. #14
    Registered User VIZHUNZ02SI's Avatar
    Join Date
    Aug 2003
    Location
    Tampa Palms, FL
    Posts
    742
    Quote Originally Posted by AUTiger View Post
    hit up 1gr8ep3, I think he is running one.
    i did but he is busy with his family for da holidays. which i understand cause i to set back my eco-builder till mid january.

  15. #15
    Site Sponsor MadLorEP3's Avatar
    Join Date
    May 2009
    Location
    The City of Angels
    Posts
    1,027
    Anything for a 07 k24a2 stock 310 injectors, aem v2 intake, dcrh for type s rsx, mugen twin loop, rbc, stock ep tranny?
    Quote Originally Posted by nmysiismyn View Post
    Ecclesiastes 1:9
    "What has been will be again,
    what has been done will be done again;
    there is nothing new under the sun."

    -King Solomon



Page 1 of 7 123 ... LastLast

Thread Information

Users Browsing this Thread

There are currently 2 users browsing this thread. (0 members and 2 guests)

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •