Close

Page 1 of 2 12 LastLast
Results 1 to 15 of 24
  1. #1
    Registered User
    Join Date
    Dec 2010
    Location
    MD, USA
    Posts
    72

    I can't remove the damn oil filter!

    So you guys know the place the oil filter is, there is no room to maneuver a channel lock or screwdriver back there while on your back, I tried laying on the engine aswell as wrapping rope around the damn thing, either way I couldn't get it off. I need some help!

  2. #2
    ephatch member MBaG's Avatar
    Join Date
    Aug 2009
    Location
    SoCal.
    Posts
    767
    take off your wheel, and go through there. you can manuver your arm straight to the oil filter, and you'll have tons of leverage too.

  3. #3
    Registered User
    Join Date
    Dec 2010
    Location
    MD, USA
    Posts
    72
    will try! Previous owner of the car had jiffy lube do the last change, They overtightened the thing so damn hard.. they should know to hand tighten only..

  4. #4
    She Will Be missed LOVIN MY EP3's Avatar
    Join Date
    Oct 2008
    Location
    San Diego
    Posts
    253
    If its really that hard I usually take a screw driver and a hammer and poke a hole threw it your gonna have to use different sizes to twist it off

  5. #5
    Registered User ep3colin's Avatar
    Join Date
    May 2010
    Location
    auburn,wa
    Posts
    287
    im pretty damn sure the manual says to tighten the oil filter to more than "hand tight"

    go to wall mart and buy yourself a 5 dollar tool that tightens down on oil filters to get them off

  6. #6
    your hero. introvert's Avatar
    Join Date
    Jan 2010
    Location
    SJ, CA
    Posts
    198
    sandpaper. works (almost) every time.

  7. #7
    GDM Lights Installed Draw7Seven's Avatar
    Join Date
    Aug 2006
    Location
    Macon, Georgia
    Posts
    1,875
    If the outside of the filter is clean, I like to use dipped gloves to get a good grip on it. I found I was never applying direct force with my hands until I could put on a pair of dipped gloves that just CLING to the outer surface and allow me to rip that sucker to the left.
    -Matt-
    2005 MR RSX-S
    Quote Originally Posted by hyu View Post
    If I wanted power I would have kept my neon

  8. #8
    Wurd.
    Join Date
    Dec 2007
    Location
    Kitchener, ON
    Posts
    1,633
    Yah, grippy gloves and then I reach up with my right arm through the lower control arm of the left suspension and my left arm near the exhaust manifold (from underneath). Swearing helps, most of the time.
    Quote Originally Posted by TexasTechEP3 View Post
    Canada has the Eh?3 Know what I'm talking aboot?

  9. #9
    Registered User beechstreet's Avatar
    Join Date
    Jan 2004
    Location
    209
    Posts
    1,415
    Quote Originally Posted by ep3colin View Post
    im pretty damn sure the manual says to tighten the oil filter to more than "hand tight"

    go to wall mart and buy yourself a 5 dollar tool that tightens down on oil filters to get them off
    overtightening filters is a no no. always do hand tight.

  10. #10
    ephatch member Falcon7's Avatar
    Join Date
    Apr 2008
    Location
    NC
    Posts
    91
    Any parts store should have a few "import" filter wrenches. Pick one of those up. and you'll be golden.

  11. #11
    * jeenyusss's Avatar
    Join Date
    May 2006
    Location
    ny
    Posts
    1,962
    i would expect nothing less from jiffy lube

  12. #12
    Registered User BeaterEP's Avatar
    Join Date
    Apr 2008
    Location
    Georgetown, TX
    Posts
    1,457
    Quote Originally Posted by shanewdude View Post
    Yah, grippy gloves and then I reach up with my right arm through the lower control arm of the left suspension and my left arm near the exhaust manifold (from underneath). Swearing helps, most of the time.
    I think that's the important step that's missing in this thread.
    If you're not prepared to make sailors blush, don't even pop the hood.

  13. #13
    Newbie Post Whoring T_Virus's Avatar
    Join Date
    Apr 2008
    Location
    Sacramento
    Posts
    3,207
    Quote Originally Posted by Aklass View Post
    So you guys know the place the oil filter is, there is no room to maneuver a channel lock or screwdriver back there while on your back, I tried laying on the engine aswell as wrapping rope around the damn thing, either way I couldn't get it off. I need some help!
    For a moment there I was lost...

    Quote Originally Posted by shanewdude View Post
    Yah, grippy gloves and then I reach up with my right arm through the lower control arm of the left suspension and my left arm near the exhaust manifold (from underneath). Swearing helps, most of the time.
    It really does. It gets you all fired up to pull that oil filter off...

    OP if you can't get it off just got to walmart/kragen/autozone and buy the oil filter remover.

  14. #14
    big block turbo club superchargedk20's Avatar
    Join Date
    Apr 2008
    Location
    2 cars ahead of you
    Posts
    2,462
    I had a k&N oil filter and i drained the oil and when it came time to take off the filter that sucker wouldnt move. After swearing at it, still wouldnt come off. So i just left it there to stew about what it was donig with no oil. After showing the oil filter no attention for a day i went back the next day wrapped a paper towel around it and the sucker came off.

  15. #15
    ephatch member RHCP0801's Avatar
    Join Date
    Apr 2008
    Location
    NY
    Posts
    2,295
    dont k&n filters have the socket thing on the bottom?

Page 1 of 2 12 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •