EM2 vs. EP3Si vs JDM EP3R spec Front Sway Bar Comparisons

[usedep3]

just thought i'd post this up. found the p/n for the jdm ep3r front sway bar: 51300-S5D-J02

[Passenger]

just thought i'd post this up. found the p/n for the jdm ep3r front sway bar: 51300-S5D-J02

How much are they going for and where can you find them? I was thinking of just doing the stock ctr front and rear sway set up.

[usedep3]

How much are they going for and where can you find them? I was thinking of just doing the stock ctr front and rear sway set up.

its like $110 plus shipping on icb.

[Andrew]

its like $110 plus shipping on icb.

and this one should clear any DC5 header right?

[Mighty_Mouse_Ep]

I am actually running a DC5 front sway i believe it is 23mm when i get home i will measure it. The stock ep is a 25mm i believe, also the dc5 front sway does have the same bends as the oem.

[usedep3]

and this one should clear any DC5 header right?

from what i've read on crsx, i know that this sway can be used to clear a jdm header like the spoon/itr/toda on a k20a. i'm trying to find out which sway would clear the same headers on a ep3/dc5. hoping wither 01/02 em2 sway, 03-05 em2 sway or jdm ep3r front sway could do this

[ep-unit]

Im not running a front sway or x-brace either. Swap forced me to part ways with it. Looking to get a swaybar back in.

I replaced the sub-frame brace to ITR spec and it greatly improved handling.

got P/N on sub frame brace?

[usedep3]

got p/n on sub frame brace?

this is the part number for the subframe brace: 74230-S6M-J00

it can be purchased through any acura stealership

[usedep3]

thanks to vicx52o i'll have an update on this thread. i'll post up pics later tonight after my GF brings home my digi-cam

could a mod edit the title to say: 'EM2 vs. USDM EP3Si vs JDM EP3R spec Front Sway Bar Comparison'

[lordofthesiths]

this is the part number for the subframe brace: 74230-S6M-J00

it can be purchased through any acura stealership

what the difference between the ours and the ITR brace?
also i looked up that part # and it just says its for a rsx not a type-R

[lordofthesiths]

Never mind i found the info here.
http://www.honda-tech.com/showthread.php?t=2680439

the Type-s and Type-R have the same brace.
It's wall thickness is more.
good pics and info at above link

[usedep3]

top to bottom: EP3R , EP3Si, EM2-15.9mm


left to right: EM2-15.9mm, EP3Si, EP3R


__________________________________________________ ______


EP3R (top), EM2-15.9mm (bottom)


EM2-15.9mm (front), EP3R (back)


EM2-15.9mm (left), EP3R (right)

[Blah1219]

I picked up the 25.4mm EM2 front sway, ingall's endlinks, ES bushings for my k24a1 swap. Hopefully the DCRH clears it.

[usedep3]

I picked up the 25.4mm EM2 front sway, ingall's endlinks, ES bushings for my k24a1 swap. Hopefully the DCRH clears it.

what was the part number for the 25.4mm EM2 sway that you picked up?

[Blah1219]

P/N: 51300-S5D-A01
I picked it up from crsx