cams/ supercharger

[05 hatch]

I just bought a jrsc street kit. I plan on swapping the pulley out for the 3.8 pulley before i put it in. My question is how will skunk 2 stage 2 n/a cams work with this setup? I have em but they're not in my car yet. Any info will help.. thanks.

[02CivicSI-VTEC]

I just bought a jrsc street kit. I plan on swapping the pulley out for the 3.8 pulley before i put it in. My question is how will skunk 2 stage 2 n/a cams work with this setup? I have em but they're not in my car yet. Any info will help.. thanks.

i had BC stage 2 cams on my JRSC setup before and it didnt gain much at all. i was losing psi and power. when i switch stock cams it made more power and psi all around.

[Panathrasher]

i had BC stage 2 cams on my JRSC setup before and it didnt gain much at all. i was losing psi and power. when i switch stock cams it made more power and psi all around.

Did you get it tuned with the new cams??? I put the BC stage2 F/I cams in mine and love them. After the final tune I lost about 2psi of boost but made nearly 20 HP. I made more torque but forget the numbers, somewhere in the neighborhood of 10 lb/tf.

[superchargedk20]

i had BC stage 2 cams on my JRSC setup before and it didnt gain much at all. i was losing psi and power. when i switch stock cams it made more power and psi all around.

I didn't make much off the bc cams either. Was raving to 8700 rpms thouh lol

[04EP3Hatch]

ill be doing the skunk2 stage 2's and supertech single springs on stock retainers (skunk2 springs are TOOOO stiff) and im curious about my results. im not going to rev past 7700 so im hoping the setup takes liking to the new sticks and makes some more powa

[firmk20]

people, people, Hold up a minute. I would advise everyone on this thread to read the post on all the forums about the junk2 cams. I personally have a friend on this forum who had the junk2 stage 2 cams, and he toasted his motor in 2 months maybe less. those cams jump the teeth and that was the end of a 270whp ep3 k frank. please do more research before you guys use those cams. check out k20a.org

[RHCP0801]

my skunk2 cams also made my motor blow, had modified tensioner and supertech dual springs and retainers. Only took 1000 miles before it took a shit

[05 hatch]

im still waiting to get my jrsc in and tuned before i put my cams in. 2nd week of march is when its goin in and getting tuned. Im gonna wait till i'm tuned to put my cams in or maybe sell em to get water/meth. I have z3 spings, ill talk to my tuner before i go with this setup. I want to hear some more info about this too.

[Panathrasher]

I didn't make much off the bc cams either. Was raving to 8700 rpms thouh lol

Where are you getting your cars tuned? I conservatively capped my redline at 7,500 rpm because my EP is my daily driver and still made good gains from the cams.

[superchargedk20]

Where are you getting your cars tuned? I conservatively capped my redline at 7,500 rpm because my EP is my daily driver and still made good gains from the cams.

I only gained about 10whp with the 4.0 pulley on my a3 with the bc stage 2 cams. When i did the 3.8 pulley and meth I saw over 20whp gains with the cams. I was the fastest a3 JRSC on this site till 04ep3hatch came along!

[XytL]

I'm hoping to see some gains with the Skunk2 Stage 1s with my JRSC-R setup when I get dynotuned these next coming days.

I currently have Skunk2 stage 1s in my car and planning on going JRSC-R with 3.8 pulley. Really interested in what you numbers are going to be, let us know!

[05 hatch]

thanks for the cam info. here's my setup for the near future. Any advice or opinions will help thanks.

jrsc (street kit) 3.8 pulley coming soon.
dc race header
3" exhaust
injen sri
thinking about 650cc injectors
might need a clutch but was wondering how much power the stock clutch can handle?

[i_love_my_ep3!]

ok soo n/a cams do work ok but you lose a little psi or boost but the hp makes up for that cool cool...