Transmission for K24A2...questions

[ryboto]

So, eventually, I'm going to swap in a K24A2. I'd planned on getting a z3 6-speed, but I've got questions...
Should I buy the whole transmission and modify it to fit?
Is there somewhere I can buy the internals for cheaper than buying the entire transmission?
What else should get replaced?(I'm a novice when it comes to engine/transmission replacement. Flywheel? Clutch? Mechanical Reverse lockout? I dunno?)

[AKEP]

buy the guts if you're up to opening the transmission. i dont feel like typing, but you'll get 6spd and lsd out of it and wont have to buy a speedo converter thingy to make it work. i tihnk you still just need the speedo ring from the ep to make it work. i think unless you have a serious set of tools to bring to a junkyard, your going to have to buy the whole transmission.

fyi you don't need to modify anything to make the z3/z1 transmission fit, the only difference is the z3/z1 use a speed sensor on the countershaft instead of the final drive. the signal comes out different than the a2/a3 transmissions, therefore. you won't be able to just plug it in and forget it though, you need a speed sensor converter box for it to function correctly. you also need wire harness where a 6spd transmission was used (type-s basically) for reverse lockout to work

[bchaney]

Yea, I would just swap the z3 internals into your ep3 case. You may be able to find the internals cheaper in a forum classified but prob not. Plus you might need some of the shaft bearings that are usually left in the case.

Get a clutch kit that includes new clutch, pressure plate, and throwout bearing. You'll want a k20a2 flywheel because more clutches are made for it - these are easily found in the classifieds on k20a.org. Resurface it and put a washer under the throwout pivot stud - talonxracer has a thread in this forum that will illustrate what I mean.

[bchaney]

Haha wow, what a coincidence - http://www.k20a.org/forum/showthread.php?t=95926

[ryboto]

Thanks for the link! Pm'd the guy, what do I need to make that work in my car? I'll look up talons thread.

[ryboto]

Thinking of pulling the trigger on this, need info on the how to get a reverse lock out with this transmission. I know I need a specific ecu, is that all? Or do I need to reflash the ecu/kpro it?

[AKEP]

that, i dont know. as far as making it work like oem...

[bchaney]

I believe you need a specific ECU and the matching engine harness. Seriously tho, it's not worth the $ or the trouble.

I was emailing him because that's a nice trans - he will go down to 1200 shipped. Email him for faster response. If I could get it for 1000 I'd be very tempted but that's only because I already have a nice setup. If I had to do it all over again - this is the trans setup I'd go with.

[ryboto]

I believe you need a specific ECU and the matching engine harness. Seriously tho, it's not worth the $ or the trouble.

I was emailing him because that's a nice trans - he will go down to 1200 shipped. Email him for faster response. If I could get it for 1000 I'd be very tempted but that's only because I already have a nice setup. If I had to do it all over again - this is the trans setup I'd go with.

So if that ecu/harness isn't worth the money should I just not do a 6speed, or just not worry about the lockout?

[ryboto]

so, sent money to the guy, now I've got to get together a flywheel, clutch, pressure plate and throwout bearing, plus a short shifter. Found a nuspeed for pretty cheap. Anyone have any opinions on an inexpensive clutch setup?

K20a2 flywheels are on k20a.org for like 40-80, or I could get something aftermarket....is the extra money worth spending if this is just a daily driver?

[Blah1219]

I hear that the lightweight flywheels drop rpms faster when clutch is in, and also has a better response. Correct me on this it has a lower idle (could be wrong). It depends on your preference. The k20a2 flywheel is a pound lighter than the k20a3, and you have a larger variety of clutches to pick from. My a2 flywheel weighs in at 15.4 lbs.

[mitchlikesbikes]

if you aren't gonna boost the k24 i'd just do a k20a2 flywheel and a nice stage 2 of some sort. keep it simple

[bchaney]

So if that ecu/harness isn't worth the money should I just not do a 6speed, or just not worry about the lockout?

I was saying I wouldn't worry about the lockout feature. That is a sweet trans setup you just picked up. I'm jealous.

if you aren't gonna boost the k24 i'd just do a k20a2 flywheel and a nice stage 2 of some sort. keep it simple

^ this. I got a k20a2 fly for 50 shipped from k20a.org classifieds, got it resurfaced for 40ish, and picked up a competition stg 2 clutch kit which includes clutch + pressure plate + new throwout bearing. I think it was 300ish.

[02TWSI]

My budget clutch setup was $90 for a resurfaced a2 flywheel from fepster, and a clubrsx oem clutchmasters clutch kit for like $180 I believe?

Seriously, reverse lockout is a joke

Go with a buddy club short shifter, nuspeed one is a joke in comparison

[ryboto]

My budget clutch setup was $90 for a resurfaced a2 flywheel from fepster, and a clubrsx oem clutchmasters clutch kit for like $180 I believe?

Seriously, reverse lockout is a joke

Go with a buddy club short shifter, nuspeed one is a joke in comparison

I'd get an OE clutch, but eventually I'd like to drop a K24A2 in the car, so I'd want one that's spec'd for higher torque than stock, right? Also, didn't read through the entire thread about it, but is the BCSS still available? The nuspeed is pretty inexpensive, what's the difference between the two?