Close

Page 4 of 9 FirstFirst ... 23456 ... LastLast
Results 46 to 60 of 121
  1. #46
    Registered User AttarixEp's Avatar
    Join Date
    Apr 2011
    Location
    Cleveland, Ohio
    Posts
    381
    Meth is so nice. Worked insanely well for me when I had my JRSC.

  2. #47
    Registered User differentK's Avatar
    Join Date
    Sep 2008
    Location
    NY / NJ
    Posts
    517
    yea im looking forward to seeing what it will do. the first JRSC setup was kind of a disappointment on the dyno because of the bad belt slip past 6000rpm... that and the belt snapped on the 2nd pull- even after all that it made 294/229. going back friday with a smaller pulley- AIS 3gal trunk mounted meth kit- and hopefully reduced belt slip.

  3. #48
    Registered User AttarixEp's Avatar
    Join Date
    Apr 2011
    Location
    Cleveland, Ohio
    Posts
    381
    Are you using the JRSC manual tensioner?
    Last edited by i02si; 03-27-2009 at 02:13 PM.

  4. #49
    Registered User mitchlikesbikes's Avatar
    Join Date
    May 2010
    Location
    Salt Lake City, Utah, United States
    Posts
    1,233
    Quote Originally Posted by AttarixEp View Post
    Meth is so nice.


  5. #50
    Registered User differentK's Avatar
    Join Date
    Sep 2008
    Location
    NY / NJ
    Posts
    517
    Quote Originally Posted by AttarixEp View Post
    Are you using the JRSC manual tensioner?
    no- modified my stock one. finding the right belt size has been a real hassle. think i have it covered now... shaved the hell out of the tensioner stops to allow even more travel and got a belt that is right on the money for the smaller pulley.... my luck it still wont be enough

  6. #51
    Registered User AttarixEp's Avatar
    Join Date
    Apr 2011
    Location
    Cleveland, Ohio
    Posts
    381
    Quote Originally Posted by differentK View Post
    no- modified my stock one. finding the right belt size has been a real hassle. think i have it covered now... shaved the hell out of the tensioner stops to allow even more travel and got a belt that is right on the money for the smaller pulley.... my luck it still wont be enough
    I remember the days of buying and returning numerous belts until finding the right one!

  7. #52
    Registered User differentK's Avatar
    Join Date
    Sep 2008
    Location
    NY / NJ
    Posts
    517
    Quote Originally Posted by AttarixEp View Post
    I remember the days of buying and returning numerous belts until finding the right one!
    yea its always fun... but you dont have to worry about that anymore

  8. #53
    Registered User AttarixEp's Avatar
    Join Date
    Apr 2011
    Location
    Cleveland, Ohio
    Posts
    381
    Belt is the least of my worries, especially finding out Forced Performance raised the price of the turbo I am planning to buy by $500

  9. #54
    Registered User differentK's Avatar
    Join Date
    Sep 2008
    Location
    NY / NJ
    Posts
    517
    saw the guys at IMW last friday for my re-tune- pretty sure i saw your block on the stand. looked fresh.

  10. #55
    Registered User AttarixEp's Avatar
    Join Date
    Apr 2011
    Location
    Cleveland, Ohio
    Posts
    381
    Yea it was mine. Derek was putting the bottoms end together. Then tore back apart. My manley rods are hitting the bottom of the sleeves so the block is back out to get notched to make clearance for them. Haha.

  11. #56
    Registered User AttarixEp's Avatar
    Join Date
    Apr 2011
    Location
    Cleveland, Ohio
    Posts
    381
    Block assembled! K24a2, plugged oil squirters, Manley turbo tuff rods(cylinders notched for clearance), CP 10.8:1 pistons (for e85), Benson sleeves.

  12. #57
    Registered User AttarixEp's Avatar
    Join Date
    Apr 2011
    Location
    Cleveland, Ohio
    Posts
    381
    Full long block assembled. Picking it up at IMW this Friday. I will have a couple pics of it then, and once its back home I will tear off the oil pan and valve cover to get a couple sneak peaks of the parts that lurk beneath. Buuuut as a teaser of what you might see, let me recap what I have so far...
    K24a2 long block assy Built by Derek (D-Rob) at IMW

    Benson sleeves 87mm bore
    Manley Turbo Tuff rods with upgraded wrist pins and ARP hardware (cylinders notched for rod clearance)
    CP Pistons 10.8:1
    K24 Crank
    Clevite Main and Thrust bearings
    ERL S2000 Oil Pump with modded oil passages required w/ K24a2 Chain and Guides
    Plugged oil squirters
    Honda TSX Head Gasket
    ARP Main Studs
    K24a2 Head resurfaced
    K20 spec Valve train
    Supertech Black Nitrate Intake Valves
    Supertech Inconel Exhaust Valves
    Supertech Seats, Retainers, Seals, Keepers
    Supertech Dual Springs
    Flow Bench Tested (No cutting of valves required or needed)
    Brian Crower Stage 2 N/A Cams
    RSX-S VTC Actuator
    Blueprint Racing 40* VTC Limiter
    Hybrid Racing Timing Chain Tensioner
    New K24a2 Timing Chain
    The rest is stock K24a2 parts (guides and such.)
    I think that's it so far...

  13. #58
    Registered User mitchlikesbikes's Avatar
    Join Date
    May 2010
    Location
    Salt Lake City, Utah, United States
    Posts
    1,233
    dat build list

  14. #59
    Registered User AttarixEp's Avatar
    Join Date
    Apr 2011
    Location
    Cleveland, Ohio
    Posts
    381
    So much, yet so much more to go.....

  15. #60
    Registered User sleepy ep3's Avatar
    Join Date
    May 2010
    Location
    Under your bed. Waiting...
    Posts
    764
    Quote Originally Posted by AttarixEp View Post
    So much, yet so much more to go.....
    Get used to it, lol. The price sheet always gets longer.

Page 4 of 9 FirstFirst ... 23456 ... LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •