anybody? I might just order the cat tomorrow and wanted to know how getting 1 would set the readiness, so i can take it back to inspection without failing again.
this is what my read out states
Misfire: Unsupported
Fuel Control: Unsupported
Comprehensive Components: Ready
Catalyst: Ready
Heated Catalyst: Unsupported
EVAP: Ready
Secondary Air Injection: Unsupported
AC: Unsupported
02 Sensor: Ready
02 Sensor Heater: Ready
EGR: Unsupported
my cat is off and am running an older version of kpro and have greddy turbo kit
so my question, what needs to be READY ? would installing my cat back on fix this issue and get what needs to be ready... READY. i did take it to the tuner to have him set readiness (i don't have laptop) drove to inspection and got the same readout as above + now a CEL just minutes after i get out of the inspection parking lot
Last edited by Nickle n Dimin; 04-06-2012 at 05:15 PM.
anybody? I might just order the cat tomorrow and wanted to know how getting 1 would set the readiness, so i can take it back to inspection without failing again.
Last edited by ghettotech; 03-30-2009 at 02:00 PM.
It's supposed to be like that. Some things aren't supported hence why it says unsupported. if u have a cel u will fail emissions. Set readiness and check through an obII scanner. If it reads what ur first post says then ur good to go. U need to find out what ur CEL is first. I've never had an issue with emissions and I have a 3in exhaust no cat and a revhard turbo kit
i went in twice to inspect the car both with the same obd2 readings from above and i get failed the CEL didn't come on till i left this afternoon. i will scan for the CEL in the morning
Last edited by Nickle n Dimin; 04-07-2012 at 12:30 AM.
And whats the reason they told u your car failed?
There's a pic of my passed inspection. Same readiness monitors as you.
i failed for overall readiness it specifically says that and only that part of the test i failed i dont get how someone with the same ready would pass .. unless it has to do with the state? ..also checked CEL it was PO171 and was cleared
Ur failing caus u need a new primary o2 sensor. Ur car isn't able to adjust fuel properly because ur primary o2 went. I'm pretty sure that's a running lean code. Even if u clear that code it will continue to pop up.
If I was you I would resest my ecu, either disconnect the battery, or through the fuse box. Drive my car for 10 -15 mins go on the highway. If theres no CEL at this point then Set ur car to readiness in kpro and immediately go to emissions.. if u still fail u need a new primary and I would Prolly get the CEL simulator as well ( I have one and have yet to fail emissions) . Regardless u need that primary fixed . I had a similar code and thank goodness I had a wideband gauge or else I would've never known I was running lean
yeah i have wide band to AEM and it just recently showed me running lean after i had tuner set readiness man i dont know what is going on now
Who's your tuner?
Relax man I had the same issue. Wideband gauge ftw! Just get urself a new primary sensor. Go to corsport they will take care of u. Thats where i got mine and never had to change it again. Over 3yrs with it now. Just get the o2 simulator while ur at it. There's an awesome write up on Clubrsx for it. It's a 5 dollar part at autozone. Everytime that code comes up just keep resetting ur ecu until u get that primary sensor.
still don't understand how my OBD2 FAILS when urs passes with the same reading
I think its because ur car has to complete a cycle before everything is ready. That primary 02 sensor is still going through its cycle before u get to emissions causing u to fail. Then when it completes its cycle ur CEL is turning on for that lean code. Only thing I can think of or ur emissions place hates u and is just failing u on purpose
There are currently 1 users browsing this thread. (0 members and 1 guests)
Bookmarks