Close

Page 1 of 2 12 LastLast
Results 1 to 15 of 29
  1. #1
    Registered User Nickle n Dimin's Avatar
    Join Date
    Jun 2008
    Location
    jersey
    Posts
    224

    Exclamation OBDII: Unsuported Readiness Help

    this is what my read out states


    Misfire: Unsupported
    Fuel Control: Unsupported
    Comprehensive Components: Ready
    Catalyst: Ready
    Heated Catalyst: Unsupported
    EVAP: Ready
    Secondary Air Injection: Unsupported
    AC: Unsupported
    02 Sensor: Ready
    02 Sensor Heater: Ready
    EGR: Unsupported


    my cat is off and am running an older version of kpro and have greddy turbo kit
    so my question, what needs to be READY ? would installing my cat back on fix this issue and get what needs to be ready... READY. i did take it to the tuner to have him set readiness (i don't have laptop) drove to inspection and got the same readout as above + now a CEL just minutes after i get out of the inspection parking lot
    Last edited by Nickle n Dimin; 04-06-2012 at 05:15 PM.

  2. #2
    Registered User Nickle n Dimin's Avatar
    Join Date
    Jun 2008
    Location
    jersey
    Posts
    224
    anybody? I might just order the cat tomorrow and wanted to know how getting 1 would set the readiness, so i can take it back to inspection without failing again.
    Last edited by ghettotech; 03-30-2009 at 02:00 PM.

  3. #3
    big block turbo club superchargedk20's Avatar
    Join Date
    Apr 2008
    Location
    2 cars ahead of you
    Posts
    2,462
    It's supposed to be like that. Some things aren't supported hence why it says unsupported. if u have a cel u will fail emissions. Set readiness and check through an obII scanner. If it reads what ur first post says then ur good to go. U need to find out what ur CEL is first. I've never had an issue with emissions and I have a 3in exhaust no cat and a revhard turbo kit

  4. #4
    Registered User Nickle n Dimin's Avatar
    Join Date
    Jun 2008
    Location
    jersey
    Posts
    224
    i went in twice to inspect the car both with the same obd2 readings from above and i get failed the CEL didn't come on till i left this afternoon. i will scan for the CEL in the morning
    Last edited by Nickle n Dimin; 04-07-2012 at 12:30 AM.

  5. #5
    big block turbo club superchargedk20's Avatar
    Join Date
    Apr 2008
    Location
    2 cars ahead of you
    Posts
    2,462
    And whats the reason they told u your car failed?

  6. #6
    big block turbo club superchargedk20's Avatar
    Join Date
    Apr 2008
    Location
    2 cars ahead of you
    Posts
    2,462
    There's a pic of my passed inspection. Same readiness monitors as you.


  7. #7
    Registered User Nickle n Dimin's Avatar
    Join Date
    Jun 2008
    Location
    jersey
    Posts
    224
    Quote Originally Posted by superchargedk20 View Post
    And whats the reason they told u your car failed?
    Quote Originally Posted by superchargedk20 View Post
    There's a pic of my passed inspection. Same readiness monitors as you.

    i failed for overall readiness it specifically says that and only that part of the test i failed i dont get how someone with the same ready would pass .. unless it has to do with the state? ..also checked CEL it was PO171 and was cleared

  8. #8
    big block turbo club superchargedk20's Avatar
    Join Date
    Apr 2008
    Location
    2 cars ahead of you
    Posts
    2,462
    Ur failing caus u need a new primary o2 sensor. Ur car isn't able to adjust fuel properly because ur primary o2 went. I'm pretty sure that's a running lean code. Even if u clear that code it will continue to pop up.

  9. #9
    big block turbo club superchargedk20's Avatar
    Join Date
    Apr 2008
    Location
    2 cars ahead of you
    Posts
    2,462
    If I was you I would resest my ecu, either disconnect the battery, or through the fuse box. Drive my car for 10 -15 mins go on the highway. If theres no CEL at this point then Set ur car to readiness in kpro and immediately go to emissions.. if u still fail u need a new primary and I would Prolly get the CEL simulator as well ( I have one and have yet to fail emissions) . Regardless u need that primary fixed . I had a similar code and thank goodness I had a wideband gauge or else I would've never known I was running lean

  10. #10
    Registered User Nickle n Dimin's Avatar
    Join Date
    Jun 2008
    Location
    jersey
    Posts
    224
    yeah i have wide band to AEM and it just recently showed me running lean after i had tuner set readiness man i dont know what is going on now

  11. #11
    432hp 360tq @14lbs Civic5lug's Avatar
    Join Date
    Jan 2005
    Location
    NJ
    Posts
    2,694
    Who's your tuner?

  12. #12
    Registered User Nickle n Dimin's Avatar
    Join Date
    Jun 2008
    Location
    jersey
    Posts
    224
    Quote Originally Posted by Civic5lug View Post
    Who's your tuner?
    pm'd you

  13. #13
    big block turbo club superchargedk20's Avatar
    Join Date
    Apr 2008
    Location
    2 cars ahead of you
    Posts
    2,462
    Quote Originally Posted by Nickle n Dimin View Post
    yeah i have wide band to AEM and it just recently showed me running lean after i had tuner set readiness man i dont know what is going on now
    Relax man I had the same issue. Wideband gauge ftw! Just get urself a new primary sensor. Go to corsport they will take care of u. Thats where i got mine and never had to change it again. Over 3yrs with it now. Just get the o2 simulator while ur at it. There's an awesome write up on Clubrsx for it. It's a 5 dollar part at autozone. Everytime that code comes up just keep resetting ur ecu until u get that primary sensor.

  14. #14
    Registered User Nickle n Dimin's Avatar
    Join Date
    Jun 2008
    Location
    jersey
    Posts
    224
    still don't understand how my OBD2 FAILS when urs passes with the same reading

  15. #15
    big block turbo club superchargedk20's Avatar
    Join Date
    Apr 2008
    Location
    2 cars ahead of you
    Posts
    2,462
    I think its because ur car has to complete a cycle before everything is ready. That primary 02 sensor is still going through its cycle before u get to emissions causing u to fail. Then when it completes its cycle ur CEL is turning on for that lean code. Only thing I can think of or ur emissions place hates u and is just failing u on purpose

Page 1 of 2 12 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •