full k24a2 build with dyno sheet.

[ep_chino]

whats up ep3hatch

i recently tuned my ep and the mods are as followed
full k24a2 tsx 06-07
Brian Crower stage 2 NA cams
type s vtc
Brian Crower dual valve springs
Brian Crower keepers
Brian Crower retainers
rbc mani
ebay SRI
full exhaust 2 1/2 to a vibrant 2 1/2
race header forgot name but decent one

tuned on 93 100* deg in shop lol
tuner yosolo


Attachment 6311

[wcmbrk]

can't see the dyno bro...nice mods though!

[ep_chino]

yeah sorry bout that i just tried again.

can't see the dyno bro...nice mods though!

[ep_chino]

IMG00408-20120629-1536.jpg

[lemonhead228]

Those numbers are really low for that set up. You should be around 240+ whp.. I seen stock set up with just i/h/e 220whp 190wtq

[1GR8EP3]

I would have to agree with lemonhead as I was guessing you would be around 230-235 but one thing I can say, it has a nice power curve. Revving it out to almost 8.5k rpm is brave, but if its holding and the motor likes it then let it loose haha.

It could also be a low reading dyno...

Its def a nice set up... cheers!

[whatsvtec]

Unfff! Dat tq plateau

Sent from my DROIDX using Tapatalk 2

[ep_chino]

yeah i agree lemonhead and 1gr8ep3 thats why i posted. i also have rdx injectors. i was thinking more around 240 hp but everyone says the heat killed me and the exhaust and the time of tunning i had stock intake. everyones stays telling me that that dyno reads low but idk how low ??? i only take to 8100!

[urthworm]

all dynos are diff, if it runs good i wouldnt worry to much. You could always take it to another dyno and see if the numbers are consistant. Alot of shops dont service their dynos (like the one in my town) and the calibrations will start to read lower.. or higher. For example the all wheel drive dyno in my town was reading torque on cars at 130% higher than what was true.

[ep_chino]

it runs good just want accurate numbers ! im goinh to do a couple pulls in a couple weeks hopefully ill see numbers i like my goal is to get 245-250 whp!!!

all dynos are diff, if it runs good i wouldnt worry to much. You could always take it to another dyno and see if the numbers are consistant. Alot of shops dont service their dynos (like the one in my town) and the calibrations will start to read lower.. or higher. For example the all wheel drive dyno in my town was reading torque on cars at 130% higher than what was true.

[gtimportfanatic]

idc how low a dyno reads, stg 2 cams on a k24a2 should be 250+ esp from yosolo. either that or your motor is seriously hurt.

[Ba82Ep3]

Ive had BC stg2's... and unless they have revised the lobes... youd be better off going back to the OEM cams... or swapping in a k20a2 head.

[USAF EP3]

Ive had BC stg2's... and unless they have revised the lobes... youd be better off going back to the OEM cams... or swapping in a k20a2 head.

What's the swap to the k20a2 head going to gain him? Smaller combustion area to raise the comp ratio? I thought all the three lobe vtec heads had the same chamber volume. I could be wrong I haven't seen anyone post info on all the different heads. I know when I built B series engines you would use a GSR head to get a slight bump in comp ratio cause the head had a smaller chamber than the B16/type r heads.

[superchargedk20]

idc how low a dyno reads, stg 2 cams on a k24a2 should be 250+ esp from yosolo. either that or your motor is seriously hurt.

yea yosolo tunes aggresive. 2 of my my freinds took there boosted k's to em, both ended up blowing. And a ephatcher has a horror story on here about them. His a2 turbo blew up while they were tuning it