Forum: DIY: section

Hi i was trying to get the light covers out and i did but it doesn't come out, like if the wiring aren't long enough to get them out. SO it there a diy post on changing the lights no the license plate?

I need a how to to installing the mugen carbon fiber front lip. Like where to cut the holes.

Hello i was wondering if anybody had info on a good DIY on installation of Front/Rear shocks having trouble taking off rears with ease.:tehehyper:

Okay I have stripped my wheels and I'm in the process of sanding them but the finish on the inside of the spokes looks like crap. Its like a dull bumpy looking surface though i have sanded it from 400 to 600 to 800 to 2000 grit and it doesnt have that shiny smooth surface that the outside spokes...

hi im new here and not entirely sure if this is the right section but i replaced my lock actuator today and now im having trouble getting the window channel back in. i thought i had it right and went to test it and now the window is completely stuck and off track a little. I cant pull it back up...

Hey guys I've been trying to find forums dealing with lip kits and fog lights. This might be a dumb question but do they make a lip that will fit with the fog lights? Some that Ive seen have been DIY and I'm not about to cut holes in my bumber and shave down my fogs? Thanks

i've been looking up DIY threads.. but none of them are detailed enough.. or in other words, they are hard to understand.. any suggestions?!

well i have read a few threads asking how to get the "shiney" back into OEM headlights. so here it is! first step is hazey headlights. http://i76.photobucket.com/albums/j26/pynikal/DSC01574.jpg http://i76.photobucket.com/albums/j26/pynikal/DSC01575.jpg...

Chunky deserves all the credit on this but unless/until he reposts his old thread, I'll post my experience. (A copy of that thread is found here: http://www.k20a.org/forum/showthread.php?t=31752 ) Based on his figures, you should expect roughly: 270cc -> 480cc 310cc -> 520cc Very inexpensive...

Tool: all you need is a small Philips screw driver First, if you have a removable steering wheel remove it, if not tilt your wheel all the way down Start off by gently pulling the top part of the black cluster trim http://i6.photobucket.com/albums/y231/Psykoasn/DSC01772.jpg Then work...

Any solutions? Clogged up? Pressure? I'm so I wasn't sure where to post this. Thanks

I did this following the instructions in the service manual (http://www.ephatch.com/forum/showthread.php?t=44979). The manual says to do it every 110k or if the valve train is "noisy" (thanks Anrasmor for looking it up). This should be done after rebuilding an engine before starting it, and...

I'm thinking about doing a rear wiper delete and wanted to get some opinions... Should I go with the Rubber Delete Plug (either DIY from Lowe's / Home Depot or this one here:...

Hey all! Thought id make a write up since the raceland craze has taken over :tehe: But first a little history, i kept getting a horrible horrible clunk after the 3rd or 4th autox on these, and i have been wondering what it was. I thought maybe blown strut. Either way, i was tearing into it the...

I thought we needed something like this so here it goes. These are Raceland Coilovers, but I'm sure any other brand will be extremely similar. Just FYI: this is my first DIY write-up for the forum. I tried to take good pictures along the way, but it is easy to forget to grab the camera at times....

DIY: 5 Lug Swap Conversion - 02/03 ep with 02/03 DC5 Type S Parts this is generation three. this DIY has been tweeked with minor changes so do your own work at your own risk. this is a suggestion, not step for step directions. Make sure you research your parts and compatibility to your car,...

This is a DIY I made to make a poor man's alarm system for under the hood. Basically, if an intruder lifts the hood the horn will go off. I did this because my car was broken into not long ago... If you want your horn to blow when someone pops your hood when you arm it, proceed......

Hey guys I was wondering what sizes are the light bulbs for the 03 ep's signal, city, and the main lights thanks.

I figured I would write up a DIY on how to make your USDM tails look like (kinda), the UKDM tails and how to integrate a rear fog light. I haven't wired up the foglight yet, so this will be an on-going DIY. Tools needed: 8mm 1/4 inch socket with extension 10mm socket, 3/8 drive flat head...