Forum: Superchargers

anyone know if i'll have any clearance problems, or any other problems, if i ran their sc on a k24a2 swap?

Hey ephatch so im thinking of supercharging my k20a3 with a "jrsc",i wanna hit 300hp at the wheels, my question is what can i do to get my motor to do that from head work to the block and trans, and please dont answer saying, "dont build the k20a3, just get a k20a2, or a k24 swap" i love my...

I have recently installed a JRSC on my ep3 and the kit came with a "6psi" pulley Which is the 4" 7 rib Pulley. I have been looking for a smaller pulley for my charger and was wondering if anyone came help cause I can't find a smaller pulley. I know they make a smaller pulley kit for the 2006 civic...

What's the part numbers for the copper ngk plugs? I have a jrsc with a 3.8 pulley. i'm running the iridium plugs now but want to swap over to copper. I'd search but I'm stuck using my phone for the Internet for now. also should I run 7 or 8 for how cold the plugs are? Thanks!

I want to upgrade my blower pulley but I'm not sure what size i should do? Also, do you need to change out anything else other than the blower pulley? I'm making great numbers with the standard 4'' pulley..... I hit 250Hp at the wheels. Ill Post the Dyno graphs

well guys im sure some of you here have seen the runs of me vs the yellow evo, he was bone stock and i beat him by 4-5 cars at about 125 or so. Well now, he has buschur intake, catless downpipe, dc 3" exhaust, hallman MBC, GSC stage 1 cams. He made 327 at the wheels on pump and 368 on e85. Now i...

I plan on gettin the JRSC street kit and K-pro. The only reason I'm not going for the Race kit is because of lame CARB (smog) regulations. So.... Any CARB outlaws out there have any advice on the issue? is it possible to pass smog with the Race Kit? I already have I/H/E and I'm hoping that...

I'm planning on JRSC on my z3 swapped EP soon. My question for you SC gurus are: 1. Are there anyone with JRSC on z3 motor here? If so, any dyno #'s? 2. Was SC for z3 motor specific or A3 modified to fit on z3(if installed on z3 swapped ep3)? My EP is a DD and have z3(6sp...

Bone stock 02. 60k clicks on the clock, would like to start making some power. How does this sound? JRSC Race Kit K-Pro some 3" CAI Race Header (what's the cheapest decent one?0

I contacted Mercracing??? and no response... I've done some research here, honda-tech, and k20a.org, but mentions of some here and there, not specific recommendations or experiences of aftercooler... So I thought I'll ask any of you with aftercooler expriences. Who makes aftercooler for our...

Today i broke a valve guide on my supercharged ep3 It knocked the valve out of place and while doing that it screwed up the top of my piston. Repair costs aren't to crazy but im thinking about building it now since i have it apart anyways Can anyone suggest a good company for -Valves...

can the lysholm twin screw supercharger fit in the ep with a aftercooler, if you cut up the radiator support just like if you were to use the rsx-s jrsc

well i am sure a few of you have followed my setup and are familiar with what im using, i made 241.3hp on the 3.8 on my stock A3. It's enough to put me a nose or so ahead of bolt-on evo's and sti's. but i want to be more than a nose. I am peaking 7.8psi, so my setup is fairly efficient as it sits,...

Well guys, after having slippage with the gatorback, i switched out to my BRAND new K070622 Gates belt, and i am having THE SAME problem :mfrown: i dont know what the hell is going on, i even took the belt off, and cleaned all the shit in the valley of the rib's on the blower pulley and the crank...

well i know dave is gonna chime in saying i told ya so :mcry: but the gatorback is very tight, and still not hitting peak boost, i spray a little belt dressing on her, and it hit's 2 more psi at 7000rpm plus. im considering sandblasting the 3.8 pulley to roughen it... or just buy this belt, didnt...

hey quick ??? for all you guys, i have a 61.5" gates micro v belt, and all it does is make the tensioner pulley squeal. WTF?? i even replaced the tensioner pulley too. Im ordering the 62.2 gatorback just to give it a shot, any one have any other ideas?

i need a 4" pulley for my jrsc let me know if you have one and give me a price please

Gonna do this tomorrow, stock is 7 rib 65.3 inch long correct? Going to mock up my stock and try to guess it from there on the belt size.

okay after my k20a2 bit the dust, i have picked up a k24a1 shortblock to rebuild my motor. since i do have the jrsc here might as well put it in since i dont have a stock IM. before my k20a2 i used the stock a2cp and a 3.2bp and made 10psi. can i use the same set up on the k24 or do i need to use...

...for a JRSC K20A3 that can run with the big boys. I made 241.3 on the 3.8 pulley with no meth on a 2.36" exhaust. Sooo now.. i will have the 3.7 pulley on a Snow Stage 2 meth kit running boost juice with a 3" exhaust. i should be able to crack the 250 mark, if not higher. By the time i am ready...

I know this may sound like a noobish question, but how do you tell if the blower is full of oil (JRSC)

I need a base map for my k20a3, JRSC, 3.8, 650cc. anyone got anything i can use to get me started?

does anyone have the comptech s/c? i was told by a shop that they can get one for me. i thought BS because i thought they were discontinued. just want to know what everyone else thinks because i know you guys are more help than any other forum. thanks in advance :mcool: