what are the potentials of this swap ..... semi built k24a4 with k24a2 head

[02 red boy]

im just waiting on my motor to come , im from the bahahamas and the guys thats doing the work has a shop in west plm beach FL thats doing the work should be finish this coming week.well first off its a k24a4 block with low compression forged pistons ,cometic gasket ,k24a2 port and polished head with 3angle job titanium valves and components and k20z3 cams,now im not a nooby at this shyt ,but i bought a brand new greddy kit before the build ,i kno ppl gonna say full race yadda yaddaa but its to late now , and we dont have that much ppl over here with ep's and I was selling the kit for half the price(NEW) , that didnt work so i figure that i will use it now my questions is with that motor set up i stated with like kpro for sure and 12-13 psi what numbers u think i cant shoot for or what if i got like a t3 t4 and mated it with the manifold and went with that , and also i will be doin fuel pump , fuel line return ,like 700ccs , and full 3inch all the way no cat either we dont have emissions tell me what u guys think as far as numbers and your positve /negative feeds ..........thnks

[POOPTOOTH]

My estimate is 300-350whp and about 250-275tq with the greddy kit and that motor. Regardless, should be a fun setup!

[02 red boy]

I already came to my conclusion on that which is why im going to get the t3/t4 turbo and mated it to my manny , nippon power has garret turbos for reasonable prices and ive seen that thier garret t3/t4 sells like for six brand new and the max output on that turbo im getting is 460hp all im shooting for is 400-375 or a lil over 4 , and im pleased

[02 red boy]

sounds gud , not bad and if i decided to switch to a bigger turbo say bout a t3 t4 cud i get close to that 400 mark with the greddy manny or it would bebest to change it

[Deadphishy]

You can make a lot of power with that set up. I don't know if you got an Intercooler with that kit. But even with the greddy manifold, and a good intercooler. You should be able to make over 400whp easy. should be able to make 300whp on about 8psi if your have a decent turbo and proper cooling.

What compression are the pistons? and what kind of rods are you using? if you are staying with stock rods, they will be your breaking point. I wouldn't go to far over the 350whp mark on stock k24a4 rods.

[02 red boy]

the guy is using forged pistons and connecting rods i dont kno the compression ratio on em , but i have pics he emailed me of the head and block i dont know how to get them up here from my email inbox but i will find out what type compression are the pistons ,also what if I jus used the greddy turbo is 350 -375 or so achievable jus guesstimating .....i will try get up or post pics or u cud mayb help with that

[02 red boy]

the pistons are wiseco compression is 9:1 and k1 rods tryna get some pics up

[chiwhitesi]

sounds like a sweet build just post some pics

[02 red boy]

yea more like a dick size 22 handgun i need a tek9 or a 357,lol but i have decided to sell it it for bout 15 new and piece toether the rest

[02 red boy]

[some pics

[chiwhitesi]

here are some pics of his build

[02 red boy]

i will takes more pics when i get the motor in my hand and of the car also and what all progress has been made....thnks chiwhite si

[sLiCk]

If I'm going to give one recommendation, toss emanage and get kpro.

[02 red boy]

emanage ,lol im ready to throw that in the garbage and havent use the emange,lol kpro is a plus and a must based on my research

[Deadphishy]

Motor looks good. Good luck with the build!