wheel/tire fitment thread

[MugsyTheGr8]

its a combination of all of those things, so all aspects should be listed. height, combined with camber and offset does make a difference.

people will end up asking, "if i'm dropped 2", will i rub with XXXX combo?" so you might as well list it.

i guess your right:noidea:

[Brian Todd]

i have no camber kit or rolled fenders.

16x7 +40
tein s tech(1.5)
225/50/16
only rubbed under hard cornering.

16x7 +45
" "
225/50/16
no rubbing at all

16x6.5
" "
225/50/16
no rubbing at all

16x8 +38(rear) 16x7 +35(front)
" "
225/50/16
rubbed in the rear any time i turned or hit a bump what ever. front cleared fine.

[jw1]

17x7.5 ET45 front and rear. 225/45/17 in the front with only minor rubbing on the plastic fender liners. Had to go with 215/45/17 to clear in the rear without rubbing. 225/45/17s in the rear rubbed like crazy. I did not roll the fenders.

[02nhbpep3]

what offset were you running jw1?

[MugsyTheGr8]

what offset were you running jw1?

his offset is 45

[powdbyrice]

bump

[SiiK20]

Im running the 99-00 Si wheels. Not sure of the offset, but know theyre 15's

I have a camber kit, but currently have 0 deg camber, and the front rubs like HELL on the fender liners. So bad a run through carbon canyon a few months ago ripped em right off. Ha

Im running 196/60/15 Dunlop's on the front

any suggestions on camber set up so i dont rub with this setup anymore?

[BlownSi05]

Wheels: Tenzo DC-6 Ver. 2 17"x7" +42 Offset
Tires: 215/45/17 Toyo Proxes 4
Drop: Rear - H&R Springs, 2" Front - Tein SSP, 2"
Alignment settings: -.75 Front and Back
Rubbing: Slightly in the Back, -1.0 camber in back or raise .5".

[RedSiBaron]

ran 225/50/16 on rsx type s 16" wheels (dont know fitment, i just know its less than stock ep3 cuz it sticks out of the wheel well more)

that was with terrible alignment and camber, specs were way off and it rubbed constantly in the 50miles to the place i was getting tires

went to 205/50/16s on the rsx type s 16" wheels and they rubbed in the rear slightly with a stock .6 negative camber in the rear but after they rubbed the edge of the tread (no cutting, gentle buffing well say) they stopped rubbing...so you can make that happen...

im also lowered 1.5inches

anyone know the offset on the 16" type s wheels?

[BlownSi05]

ran 225/50/16 on rsx type s 16" wheels (dont know fitment, i just know its less than stock ep3 cuz it sticks out of the wheel well more)

that was with terrible alignment and camber, specs were way off and it rubbed constantly in the 50miles to the place i was getting tires

went to 205/50/16s on the rsx type s 16" wheels and they rubbed in the rear slightly with a stock .6 negative camber in the rear but after they rubbed the edge of the tread (no cutting, gentle buffing well say) they stopped rubbing...so you can make that happen...

im also lowered 1.5inches

anyone know the offset on the 16" type s wheels?

those should be the same offset as our 04/05 stocks. +45 i believe.

[bmyers4321]

Work Emotion Cr Kai
17x8 +42
225/45/17 BFG G-force Sports
H&R=2"
no rolled fenders
need an alignment

[MugsyTheGr8]

are you rubbing at all?

[bmyers4321]

very little. only when making real hard turns. i do for some reason rub a little when turning around 2 corners in my neighborhood its kinda weird.

[bdooley]

Im not rubbing lol! konig daylights in 15 x 6.5 with an offset of +40. tires are 205/50/15

[MugsyTheGr8]

Im not rubbing lol! konig daylights in 15 x 6.5 with an offset of +40. tires are 205/50/15

pics or bs.