very nice write up! so, any 2.2 ohm resistor would work to bypass an srs component? i have an after market wheel and i would love to shut the srs light off.
Hey guys, this is a how to on replacing your SRS pre tensioner/OEM seatbelt buckle with a non SRS unit for use with an aftermarket bucket seat or when using harnesses. Using this how-to will allow you to remove the unit while still keeping the rest of the SRS system functional, and will turn off the seatbelt light on the gauge cluster.
The reason for replacing this unit is that it cannot be properly and safely mounted on a bucket seat due to the mounting not being the same as our stock seats. Also, at least with my seat (Memoryfab S68) the OEM buckle is far too high to be able to pass the oem belt through the right side harness hole so the belt is tight against my waist.
In case you guys are having this same issue you can use a driver or passenger side male buckle from a Mitsubishi Lancer Evo 8. Im not sure what other buckles will work but from what Ive seen no other non SRS Honda female buckles will work with the EP3 male buckle.
Here is the EP3 male buckle vs. the Evo 8 buckle...
.
.
Now onto the wiring...
*Always disconnect your battery before doing any work on the SRS system*
*If for some reason you need to reset your SRS light here is a How-To on doing so - http://www.ephatch.com/forum/showthr...ight=reset+srs
You can either do what I did and make a plug and play jumper with the female side of the plug or you can simply stick some leads into the male plug. I prefer making it look and function as close to OEM as possible.
I started with the SRS plug. All you need to do with this (and bypassing pretty much any SRS component) is jump it with a 2.2 ohm resistor. This plug is mounted to the bottom of the seat.
.
.
Next up are the leads for the buckle itself (ground, seatbelt light signal, and SRS signal).
You will need to remove the dash light lead (center lead - blue/red tracer) and jump the SRS lead (left lead - red/blue tracer) to ground (black). This plug will be mounted beside the SRS plug.
.
.
And here we go... Both jumpers installed. Nice and clean!
.
.
Tucked away!
very nice write up! so, any 2.2 ohm resistor would work to bypass an srs component? i have an after market wheel and i would love to shut the srs light off.
Green Crew #7
Please donate and support EPHatch.com: Greenie Status, License Plate Frames, Banner & Small 'ephatch.com' Decals
Was your WTS/WTT/WTB closed? Please read the following: link 1 & link 2
Thanks! And yes all Honda SRS components supply a 2.2ohm resistance for the system check when you turn the key to the on position. All you would have to do is unplug the yellow connector for the airbag and jump it with the resistor. If you cant find resistors let me know. I had a hard time finding the 2.2's but luckily a buddy of mine had a bunch of them laying around and hooked me up.
I transferred my seat belt assembly to my rsx type-s leathers. Can i still do this if im using the stock seat belt assembly? I dont really underatand this but id like the rest of my airbags to still work.
As always great job!
Yup a reset will have to happen if your light was on prior to the install.
give a reset and you should be all set.
be jealous :P
Yup this doesnt automatically reset the light, you will have to do that manually via the link I included in the OP. It can be tricky, if you dont do it just right it doesnt work. I actually made a little jumper out of an extra plug I had so I could just clip it on and off easily to do the reset. (I had to do it a bunch of times when I was experimenting with the 3 wire plug)
Tried the reset, no luck. And i know it worked because it flashed saying it was successful.
Can you make me one for my steering wheel I need to turn the light off....
No because ive reset it before and it was fine. Maybe theres somethin wrong somewhere else. I guess ill worry about it when the time comes. Shes sittin in the backyard with a grenaded 48k mile a3:(
There are currently 1 users browsing this thread. (0 members and 1 guests)
Bookmarks