Close

  • Cleaning the IAC

    Results 1 to 15 of 80

    Hybrid View

    Previous Post Previous Post   Next Post Next Post
    1. 06-23-2010, 12:42 PM #1
      oneglory
      oneglory is offline
      Site Sponsor oneglory's Avatar
      Join Date
      Apr 2004
      Location
      NJ
      Posts
      1,470
      did you do the proper idle relearn procedure?
      Ed~
      Reply With Quote Reply With Quote
    2. 06-23-2010, 03:21 PM #2
      SUSHI_NE1
      SUSHI_NE1 is offline
      A.K.A. SICIVICGUY SUSHI_NE1's Avatar
      Join Date
      Apr 2009
      Location
      Santa Monica
      Posts
      277
      Quote Originally Posted by oneglory View Post
      did you do the proper idle relearn procedure?

      i did.... Held the gas down at 3k untill fans come on, then let it sit for 5 minutes.

      That sound about right?
      Reply With Quote Reply With Quote
    3. 06-23-2010, 05:34 PM #3
      talonXracer
      talonXracer is offline
      ΜΟΛΩΝ ΛΑΒΕ talonXracer's Avatar
      Join Date
      Apr 2004
      Location
      Catskill Mtns
      Posts
      9,252
      The proper procedure is to get the engine to operating temp, reset the ECU and keep the RPM's to 3K for 3 Minutes time, adding any time the fans are on to the three minutes.
      ALL advice issued with this "Disclaimer"
      Tim "the Toolman" Taylor is my HERO ! ! !

      "Labor Unions are Domestic Terrorist orgainizations"
      Reply With Quote Reply With Quote
    4. 07-27-2010, 10:07 AM #4
      bchaney
      bchaney is offline
      k24 ep3 bchaney's Avatar
      Join Date
      Apr 2008
      Location
      tx
      Posts
      784
      I might pick up a set of these if I'm gonna have to be cleaning this out as often as you say.

      http://www.amazon.com/Silverhill-Poi.../dp/B002P4YCGM
      Reply With Quote Reply With Quote
    5. 12-01-2010, 07:37 PM #5
      evanr821
      evanr821 is offline
      Registered User evanr821's Avatar
      Join Date
      Apr 2009
      Location
      Upland, CA
      Posts
      25
      Quote Originally Posted by bchaney View Post
      I might pick up a set of these if I'm gonna have to be cleaning this out as often as you say.

      http://www.amazon.com/Silverhill-Poi.../dp/B002P4YCGM
      Forget that...i took out those screws and replaced em with the same ones but they have a 7mm hex head. Cost about $3 at autozone.
      Reply With Quote Reply With Quote
    6. 12-14-2010, 08:59 PM #6
      skoo74
      skoo74 is offline
      無限SKOOGEN skoo74's Avatar
      Join Date
      Jun 2004
      Location
      Lot 52, Thailand Refugee Camp
      Posts
      359
      bump.. just cleaned it again and runs good again... this time it only took me an hour total!... last time was like 3 hours to take off, clean and put back together...
      Reply With Quote Reply With Quote
    7. 12-16-2010, 01:38 PM #7
      T_Virus
      T_Virus is offline
      Newbie Post Whoring T_Virus's Avatar
      Join Date
      Apr 2008
      Location
      Sacramento
      Posts
      3,207
      Quote Originally Posted by skoo74 View Post
      bump.. just cleaned it again and runs good again... this time it only took me an hour total!... last time was like 3 hours to take off, clean and put back together...
      Help clean mine...I don't have tools...lol...
      Reply With Quote Reply With Quote
    « Previous Thread | Next Thread »

    Thread Information

    Users Browsing this Thread

    There are currently 1 users browsing this thread. (0 members and 1 guests)

    Bookmarks

    Posting Permissions

    • You may not post new threads
    • You may not post replies
    • You may not post attachments
    • You may not edit your posts
    •  

    Forum Rules